Models
>
VVSR1030H5WO
VVSR1030H5WO Hotpoint Washer - Overview
Sections of the VVSR1030H5WO
[Viewing 4 of 4]
Keep searches simple, eg. "belt" or "pump".
Tub Dampening Strap
PartSelect #: PS271100
Manufacturer #: WH1X2727
The tub dampening straps support the wash tub and reduce vibration by keeping the tub at the center of the cabinet. If your washer shakes and moves, or is making a loud banging noise during the wash c...
$9.61
In Stock
D-Shaped Knob Clip
PartSelect #: PS268493
Manufacturer #: WH01X10106
This clip ensures that the knob is securely fastened to the control shaft, allowing you to properly select the correct time and setting for your dryer. If your dryer will not start or shut off, the ti...
No Longer Available
Drain Hose
PartSelect #: PS890597
Manufacturer #: WH41X10096
The drain hose is black in color and made of flexible material. This is a part for your top-load washer. The hose measures 57 inches long. This part moves the water out of the washer and into the drai...
$27.09
In Stock
Tub Seal
PartSelect #: PS4704237
Manufacturer #: WH02X10383
The main tub seal is located between the transmission and the outer tub. Its the primary water seal in the outer tub for the transmission-shaft. If your washer is leaking during the fill cycle, or at ...
$16.73
In Stock
V-Style Drive Belt
PartSelect #: PS270803
Manufacturer #: WH1X2026
This V-shaped drive belt is 29 1/2 inches long x 1/2-inch-wide, and fits both front-load and top-load washing machines. When belts are worn or frayed, they are known to make noise. If you have a top-l...
$14.10
In Stock
Knob and Clip
PartSelect #: PS1482289
Manufacturer #: WH01X10313
This knob accepts a D-shaped shaft.
$13.04
In Stock
Tub Bearing Washer
PartSelect #: PS271509
Manufacturer #: WH2X1197
This is a tub bearing and it is meant to work in conjunction with your washing machine. The purpose of this part is to aid in keeping the inner tub of your washing machine spinning smoothly during a w...
$9.97
In Stock
Split Ring
PartSelect #: PS1766022
Manufacturer #: WH02X10265
This split ring is supplied by the original equipment manufacturer, and it is designed to secure the tub bearing in washing machines. It is a circular metal ring, with an outer diameter of 2 inches. T...
$14.41
In Stock
Tub Bearing
PartSelect #: PS271510
Manufacturer #: WH2X1198
This tub bearing goes in your washing machine. You will find it on the bottom of the outer tub, where the transmission goes through the tub. If you hear metal on metal when the washer is spinning, you...
$27.53
In Stock
Agitator Coupling
PartSelect #: PS1482517
Manufacturer #: WH43X10032
Bolt not included. This part connects the transmission drive shaft to the agitator base.
$25.63
In Stock
Compression Ring
PartSelect #: PS652828
Manufacturer #: WH02X10093
Used in conjunction with the timer dial knob assembly.
$19.31
In Stock
Pump to Tub Inlet Drain Hose
PartSelect #: PS11721808
Manufacturer #: WH41X22935
This replacement inlet drain hose connects your washer's water pump to its tub. This hose is seven and a half inches in length and only two inches wide.
$16.95
In Stock
Questions And Answers for VVSR1030H5WO
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the VVSR1030H5WO
[Viewing 10 of 10]Leaking
Fixed by
these parts
these parts
Show All
Will not agitate
Fixed by
these parts
these parts
Show All
Burning smell
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Spins slowly
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Shaking and Moving
Fixed by
these parts
these parts
Show All
Marks left on clothes
Fixed by
these parts
these parts
Show All
No hot or cold water
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
GE washer no spinning during spin cycle
Used the spatula to release the front panel (push flat spatula under top about 2 inches from either side to release the two sprng clips holding the front panel on) to expose the tub and motor assembly. Inspected the belt and it seemed worn and a lot of rubber particles were in base of machine. Ordered the belt from partselect - received i
... Read more
t two days later. Loosened 4 motor mount nuts. Removed old belt and replaced. Tightened belt and tightened nuts on motor. Only tricky part is you will need extensions for socket drive because belt is in the way for two of the motor mount nuts. I used a 1/4" small socket wrench, with an extension. No expertise needed on this one.
Read less
Parts Used:
-
Laurence from Bronx, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
171 of 190 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bearing on the transmission to tub wore out (mostly due to the washer not being level)
The back of the control panel had an instruction pamplet that was very useful. 2 parts did not go as written tho. To "pop" the spinner out, required short 1x4s and a shake/shingle bar to pry it up and the wedging of the 1x4s under it, until enough strain was put on it to "pop" it off. Then the large 1&11/16 nut was a bear. It require
... Read more
d a short pipe wrench (so it fit in the tub) and a hammer to brake it loose.
Read less
Parts Used:
-
Victor from League City, TX
-
Difficulty Level:Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
89 of 105 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washer was not agitating or spinning
My washer was making noise but not agitating or spinning on any of the cycles that I turned the dial to. Didn't know if it was the transmission or something simple. I did some research and discovered it may be the belt, even though the belt looked new, I changed it anyway by just removing the front of the washer and cutting the belt off a
... Read more
nd putting the new belt on by just turning the pulleys until it fed on. No need to tip it over to do the repair...and it WORKED!! Then I did the happy dance around the house...see woman can repair 2!
Read less
Parts Used:
-
Rachelle from Kent City, MI
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
60 of 64 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!