Models
>
TEC3X3XCWA
TEC3X3XCWA Tappan Cooktop - Overview
Sections of the TEC3X3XCWA
[Viewing 4 of 4]
Keep searches simple, eg. "belt" or "pump".
Drip Bowl - 8"
PartSelect #: PS437595
Manufacturer #: 316048413
This chrome drip bowl is designed for use with electric cooktops and ranges. This drip bowl is sold individually. At the widest point this part has a diameter of approximately 10 inches. It sits benea...
$12.59
In Stock
Terminal Block Kit
PartSelect #: PS470125
Manufacturer #: 5303935058
This part connects the wire harness to the surface element and is used for ranges. The kit includes interchangeable mounting brackets, ceramic wire nuts, heat shrink protective tubing, and wires. If y...
$16.24
In Stock
Drip Bowl - 6"
PartSelect #: PS459618
Manufacturer #: 5303280336
This part is located beneath the heating element on your range, and is designed to catch any spills. If your current drip bowl is worn or stained, consider replacing it. This heavy chrome drip bowl is...
$7.46
In Stock
Burner Switch Kit
PartSelect #: PS470145
Manufacturer #: 5303935086
This is a burner switch kit, also known as the surface element control switch repair kit, for ranges. This burner switch kit sends voltage to the surface element coil and it controls the stove top sur...
$40.14
In Stock
Surface Burner Coil Element - 8" - 2100W
PartSelect #: PS473948
Manufacturer #: 5308011964
$152.66
In Stock
Questions And Answers for TEC3X3XCWA
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the TEC3X3XCWA
[Viewing 3 of 3]Element will not heat
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Old pans/bowls were corroded
Very easy---simply unplug the burners, remove the old pans and replace with the new ones
I was extremely pleased with the easy ordering and prompt delivery of parts that actually fit as they should!
I was extremely pleased with the easy ordering and prompt delivery of parts that actually fit as they should!
Parts Used:
![](https://partselectcom-gtcdcddbene3cpes.z01.azurefd.net/437595-1-S-Frigidaire-316048413-Drip-Bowl-8-amp-quot.jpg "Drip Bowl - 8" – Part Number: 316048413")
-
John from Nisswa, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
48 of 53 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
High heat reluctant to turn down.
Most of the job is simple fastener mechanics.
Use a nut driver or Phillips screwdriver. Remove rear panel.
Pull out control knob. If it is stuck, wrap a small rag around the back of it and pull the rag steadily.
Carefully match marked terminals on the replacement switch with those on original. Switch terminals ... Read more may not be in the same location. Replace wires one for one, one at a time.
Carefully select the correct knob filler for the switch post. Several are supplied. Proceed with logic and measure the shaft length and the filler length and type to match.
Use a nut driver or Phillips screwdriver. Remove rear panel.
Pull out control knob. If it is stuck, wrap a small rag around the back of it and pull the rag steadily.
Carefully match marked terminals on the replacement switch with those on original. Switch terminals ... Read more may not be in the same location. Replace wires one for one, one at a time.
Carefully select the correct knob filler for the switch post. Several are supplied. Proceed with logic and measure the shaft length and the filler length and type to match.
Read less
Parts Used:
-
George from New Port Richey, FL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
45 of 49 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Right front burner would over-heat
First of all I removed the top panel then removed the switch. I then took pictures of the switch & drew a sketch with all the info. Then I went to your web site, matched up the switch & ordered.
When the switch arrived I went thru the above replacing the bad switch.
When the switch arrived I went thru the above replacing the bad switch.
Parts Used:
-
Melvin from Attica, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
23 of 27 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!