Models
>
SVD48600B
SVD48600B Jenn-Air Range - Overview
Models starting with SVD48600B
Click on the best match to narrow your results.
Keep searches simple, eg. "belt" or "pump".
Light Bulb - 40W
PartSelect #: PS884734
Manufacturer #: 8009
This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these replacement bulbs are mos...
$11.73
In Stock
Grease Filter
PartSelect #: PS11743870
Manufacturer #: WP71002111
This filter is made of metal and is intended for use with ranges and cooktops. Grease filters are an important but often neglected part of ranges. If the filter is full, your extractor fan will become...
$30.69
In Stock
Long Oven Sensor
PartSelect #: PS1570174
Manufacturer #: 12001656
This long oven sensor is also commonly known as a temperature sensor. It is designed for use with ovens and ranges. It is similar to a thermostat; it measures and regulates the internal temperature of...
$34.75
In Stock
Screw, 8/18 x 3/8
PartSelect #: PS11746840
Manufacturer #: WP90767
This screw is sold individually.
$5.42
In Stock
Single Door Strike
PartSelect #: PS11743868
Manufacturer #: WP71002097
This door strike is less than an inch long. It is all white in color and it is made entirely of plastic. The door strike fits on the inside of your range and is the locking mechanism that latches to t...
$14.78
In Stock
Electronic Clock Control Board
PartSelect #: PS11743858
Manufacturer #: WP71001799
This oven control board and clock is for ranges.
Oven control board and clock monitors the oven temperature and controls the oven heating functions in the range, and includes the digital display fo...
$415.40
In Stock
Gas Valve Knob
PartSelect #: PS11743848
Manufacturer #: WP71001057
This gas valve knob measures approximately 2 12 inches in diameter. It is a black knob that has white lettering aroud its perimeter denoting the different temperature levels: low, medium, high, etc. T...
$32.40
In Stock
Screw
PartSelect #: PS12349731
Manufacturer #: W11233072
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$20.79
In Stock
Double Burner Pan - Black
PartSelect #: PS2356975
Manufacturer #: 3401X055-09
This pan sits under the burner to catch anything that may spill over to make cleaning up easy. Also known as Aeration Pan. Sold individually.
$202.45
In Stock
Front Burner Assembly - Black (Glossy Finish)
PartSelect #: PS11744567
Manufacturer #: WP7505P283-60
This black front burner assembly is nine inches long. It is used with Maytag brand gas ranges.
$212.71
In Stock
Rear Burner
PartSelect #: PS1647215
Manufacturer #: 74005189
This black burner head has a glossy finish.
$316.92
In Stock
Bake Element - 240V
PartSelect #: PS11743855
Manufacturer #: WP71001680
The element has male terminals. This bake element is found on the bottom of the oven.
$92.60
In Stock
Common Symptoms of models starting with SVD48600B
[Viewing 12 of 12]Little to no heat when baking
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Oven is too hot
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Touchpad does not respond
Fixed by
these parts
these parts
Show All
Will not program
Fixed by
these parts
these parts
Show All
Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Little to no heat when broiling
Fixed by
these parts
these parts
Show All
Door won’t open after self cleaning cycle
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Timer will not advance
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Replace Grease Filter
Just a couple of minutes to left off the cover grid, left out the old filter and drop in the new one.
Parts Used:
-
Gene from Washington C.H., OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
524 of 537 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven not holding 350 F, when cooling the coils did not reheat
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening,
... Read more
reinstall 2 screws. The oven works fine! Note that due to thermal lag the temperature overshoots to 370 degrees and undershoots to 340 degrees, this appears to be normal oven operation. Putting door back in place was easy.
Read less
Parts Used:
-
David from Westford, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
156 of 196 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lost all clock and timer display
Removed the 4 phillip head screws that hold the trim plate on the bottom of the display panel (and you probably could skip this step).
Next, I removed the knobs from the front of the display panel.
Then I removed the 4 phillip head screws that were located (1 each) behind the knobs.
Finally, I removed the 4 hex head screws ... Read more from the bottom of the front panel.
You caan then remove the panel a few inches and remove the two cable connectors.
The trick part is to get the flat ribbin cable disconnected. If you squeeze the two small tabs (one on each end of the connector), the connector moves up and spreads open to CAREFULLY remove the ribbon cable.
The clock assembly has just two hex head screws holding it in place. Remove them, and reassemble everything in reverse.
If you did everything correctly, you should have a very bright stove clock again!
Next, I removed the knobs from the front of the display panel.
Then I removed the 4 phillip head screws that were located (1 each) behind the knobs.
Finally, I removed the 4 hex head screws ... Read more from the bottom of the front panel.
You caan then remove the panel a few inches and remove the two cable connectors.
The trick part is to get the flat ribbin cable disconnected. If you squeeze the two small tabs (one on each end of the connector), the connector moves up and spreads open to CAREFULLY remove the ribbon cable.
The clock assembly has just two hex head screws holding it in place. Remove them, and reassemble everything in reverse.
If you did everything correctly, you should have a very bright stove clock again!
Read less
Parts Used:
-
John from Kuna, ID
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers, Socket set
85 of 91 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!