Models
>
MGC5430ADC
MGC5430ADC Maytag Cooktop - Overview
Sections of the MGC5430ADC
[Viewing 3 of 3]
Manuals & Care Guides for MGC5430ADC
Click to downloadKeep searches simple, eg. "belt" or "pump".
Top Burner Igniter
PartSelect #: PS2082000
Manufacturer #: 74004053
This is a surface burner igniter, also known as a top burner ignitor and stove top spark electrode. It is used to generate the spark that lights the surface burner. If your stove will not start, eleme...
$41.20
In Stock
Rubber Grommet
PartSelect #: PS2202491
Manufacturer #: Y8007P02060
Used as the bottom feet of a gas stovetop grate. Sold individually.
No Longer Available
Burner Head Cap with Spark Electrode
PartSelect #: PS11741732
Manufacturer #: WP3412D024-09
The burner head cap with spark electrode directs the gas to the front and back burner heads and will equally distribute the gas across cooking areas. This part can help the following symptoms: if your...
$67.94
In Stock
Screw
PartSelect #: PS12349731
Manufacturer #: W11233072
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$20.79
In Stock
Spark Module - Surface Burners
PartSelect #: PS2003170
Manufacturer #: 12001596
This part may differ in appearance, but functions same as original part. : This part sends enough current to the igniter to create a spark to the bottom of the burner cap.
$61.76
In Stock
Burner with Electrode
PartSelect #: PS11741730
Manufacturer #: WP3412D021-09
This sealed burner is used on some gas ranges and cooktops. This design does not require a burner cap. The burner electrode is also included with this item. No gasket seal required per manufacturer.
$145.81
In Stock
Burner Cap - Black
PartSelect #: PS11741672
Manufacturer #: WP3403F088-00
This burner cap is three inches in diameter. It is made of a ceramic material and is coated in a black enamel substance. This is a genuine OEM part and is sold individually.
$47.29
Special Order
Screw
PartSelect #: PS11751203
Manufacturer #: WPW10253196
Sold individually. This screw is half of an inch long. It is made of metal and it is intended for use with some Maytag brand ranges.
$4.68
Special Order
Surface Burner Knob
PartSelect #: PS2080300
Manufacturer #: 74001299
Sold individually. This knob accepts a D-shaped shaft.
No Longer Available
Burner Switch
PartSelect #: PS11744495
Manufacturer #: WP7403P367-60
Order quantity required.
$76.03
In Stock
Igniter Wire
PartSelect #: PS11742785
Manufacturer #: WP5111A360-60
This igniter wire is twenty-eight inches long.
No Longer Available
Questions And Answers for MGC5430ADC
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the MGC5430ADC
[Viewing 4 of 4]Will Not Start
Fixed by
these parts
these parts
Show All
Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Gas smell
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
gas burner ignitor failure
Lift out sealed burner assembly rear of stove first while careully sliding to rear to disengage ignitor probes.Remove philips head screws from bottom sheet metal housing to expose bottom of burners Remove gas tube assembly screws and move tube away carefully.Unplug wires from ignitor.Remove screws for ignitor .Remove ignitor, I noticed t
... Read more
hat rust and dirt had built up around burner to pan connection.I used my oil filter wrench to turn slightly the burner to remove it from the pan to clean.Reassembled in reverse order.
Read less
Parts Used:
-
roy from East Providence, RI
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
139 of 157 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No spark at top burners, first one then eventually all 4.
Most of the repair time was spent researching the problem online, locating the spark module inside the range, and selecting the part online. Installation was easy. Key troubleshooting info for me was, if there is no clicking, the spark unit is probably worn-out. I traced the ignition wires from the burners down to the spark module, locate
... Read more
d inside a 2x3" metal housing next to the bottom drawer. I removed 2 screws and out it came. The replacement unit pictured on the PartSelect site was not identical to the original but had the same number of contacts. I ordered the part and it arrived a few days later. The old connectors slipped easily onto the new pins, and I screwed the new unit into the range using the new metal housing. All 4 burners now spark up quickly, and we saved at least $100 on a service call. It was well worth the time and effort -- thanks!
Read less
Parts Used:
-
jonathan from Bryson City, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
32 of 37 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner wouldn't start
Make a quarter turn counterclockwise, disengage a burner head, disconnect 2 wires, connect to a new head, install turn clockwise.
That's it!
That's it!
Parts Used:
-
Yury from Brooklyn, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
35 of 48 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!