If your gas dryer is not heating up or igniting, then replacing the flame sensor, located in the burner assembly, could solve it. This part senses heat from the igniter to monitor if it is hot enough ...
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
This idler pulley assembly is sourced from the original manufacturer for use in dryers. The assembly includes the pulley wheel and bracket. It is found near the motor where it provides tension to the ...
This conversion kit contains all parts needed to convert your gas dryer from natural gas (NG) to liquid propane (LP). This kit will work with some Samsung dryers as well. Use model # to ensure you are...
This part is the replacement thermal fuse for your dryer. When you order this part, you will receive the fuse itself, as well as the bracket that mounts it to the dryer. The thermal fuse is approximat...
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Brenda
February 5, 2020
Our gas Maytag dryer comes up with an error code do. What dies that mean ?
For model number MDG9700AWW
Hello Brenda, thank you for your question. That error code is in relation to the door being open. The unit is not recognizing the door is closed. Be sure the door is latched shut. If it is and the error continues after unplugging the unit for about 5 minutes then plugging it back in the door switch should be replaced. That is PartSelect Number PS11741823. Good luck with your repair
My gas dryer. The igniter works, but I get no flame.
For model number MDG9700AWW
Hi John, thank you for your inquiry. According to our research, the issue is most probably with the flame sensor, part number PS11741429. You may need to replace it to fix the issue. Glad to be of assistance!
Callled the service company to diagnose the problem. Watched him take machine apart. He found the problem. Told me the parts that I needed. Didnt know what they were. Went to partselect.com looked my model up and found parts and ordered. Followed same steps as repair guy: Two screws in back of machine then slide top off. Six screws in
... Read morefront to remove front door ( 4 screws on top 2 on bottom) Changed the thermostat and thermistor. Saved 320 dollars :)
From what I understand, this is a common problem with this Samsung made Maytag Neptune dryer. The dryer was making a sound like it had a shoe in it every time it was drying. The crack was in the seam at the back of the drum behind one of the baffolds so you can't see it when you look inside. I did not see it until I took the top off th
... Read moree dryer, looked inside and saw light through the hole. To take the dryer apart, first unhook it from the wall, gas, electricity, and exhaust. Remove 2 skrews from the top back side and slide the top of the dryer back and remove. The plastic control panel is then removed by taking 2 skrews out from the top, pulling the top of the control panel forward and reaching in with the other hand to pop out the plastic clips of the control panel from the front face of the dryer. Unplug the control panel from the electrical panel inside the dryer. Then you can remove the front door, 2 skrews, remove the front panel, 8 skrews I think, then the front piece the the drum rides on, 1 skrew. Take the belt loose and the drum will come right out. To install just reverse. Pretty easy once I figured out how to remove the control panel. I think the reason for the drum crack is it looks as though the back pressed metal piece that the drum rides on is not perfectly round. Even the new drum makes a very light thump sound and when I watched it go around with the top off the dryer I could see the drum turn slightly oblong. Check your wheels and make sure the axles are not worn, if they are, replace them at this time. Also you might as well replace the belt too.
Remove dryer covers and locate heater assembly. Removed heater assembly and checked visually if the heater coil is opened, I verified this with an ohm meter. Heater Continuity was OK. Next step I checked the heater sensors. Thermal fuse with bracket had no ohm meter reading between two terminals[open circuit]. Order part#35001193 "thermal
... Read more fuse" with bracket from "partsSelect.com." Assemble back in reverse order. Please note that the dryer heater was filled with lint and needed a good cleaning.