Models
>
KGCT366EAL0
KGCT366EAL0 KitchenAid Cooktop - Overview
Sections of the KGCT366EAL0
[Viewing 3 of 3]
Keep searches simple, eg. "belt" or "pump".
Burner Grate Pads - Kit of 5
PartSelect #: PS389174
Manufacturer #: 814323
These pads go on the bottom of your gas cooktop grates to prevent them from moving and scratching the top of your appliance.
$8.38
In Stock
Knob Skirt - Black
PartSelect #: PS11731279
Manufacturer #: W10854242
The knob skirt or grommet on your range goes around the knob, forming a buffer between it and the range surface. If your knob skirt is damaged, you should consider replacing it. This product is approx...
$11.18
In Stock
Knob Skirt
PartSelect #: PS11740833
Manufacturer #: WP3180081
This white knob skirt is located between the glass top and the control knobs of your stove top. The skirt has an outside diameter of approximately 2 inches. The most common reasons to replace the time...
$11.07
In Stock
Control Knob
PartSelect #: PS11740843
Manufacturer #: WP3182567
This part is a black plastic knob that is most often used as a burner control knob. This knob allows you to turn the burner on your range or cooktop on, and it allows you to control the temperature of...
$24.75
In Stock
Control Knob
PartSelect #: PS11740844
Manufacturer #: WP3182568
Sold individually. This knob can accept a D-shaped shaft.
$25.38
In Stock
Spark Electrode
PartSelect #: PS11740866
Manufacturer #: WP3185804
This part helps your burner ignite and produce flame.
$49.02
In Stock
Burner Control Knob
PartSelect #: PS11740845
Manufacturer #: WP3182569
Sold individually. This knob takes a D-shaped shaft.
$31.39
In Stock
Knob Skirt - Black
PartSelect #: PS11731278
Manufacturer #: W10854241
NOTE: No longer available in biscuit or white. Black only.
$9.10
In Stock
Gas Valve/Switch Seal Cover
PartSelect #: PS11740880
Manufacturer #: WP3188425
Part is located on top of the igniter switch that's next to the gas valve. Helps regulate gas flow and the amount of normal leakage that may occur.
$35.28
In Stock
Spark Module
PartSelect #: PS11748330
Manufacturer #: WPW10110486
This part sends enough current to the igniter to create a spark to the bottom of the burner cap.
$155.85
In Stock
Spark Switch
PartSelect #: PS11740890
Manufacturer #: WP3190779
When the gas burner valve knob is depressed and turned, this part creates a spark that lights the gas and starts the burner.
$57.52
In Stock
Questions And Answers for KGCT366EAL0
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the KGCT366EAL0
[Viewing 3 of 3]Will Not Start
Fixed by
these parts
these parts
Show All
Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
several grate pads fell out/lost /broke during cleaning
The only real issue was locating the proper adhesive to ensure that the new pads would not fall out. The small insert paper slip in the package noted that a RTV adhesive should be used. After much searching at the home improvement super store, I learned it would be found at an auto supply store. It is black, and is for high temp use. It i
... Read more
s available in a small tube for around $2.00. The RTV is usually used to make gaskets for heat/oil exposure in auto repair. I did have trouble removing a broken stub from a pad that had broken off in the hole. I used an awl to get what I could and push the rest into the hole deeper, then insert a new pad with along with the adhesive.
Read less
Parts Used:
-
Sabrina from Mooresville, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
61 of 67 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
There was a crack in the porcelain not letting it spark
I used a screwdriver to pry the electrode assy. out of the burner. then disconnected the wire.
Then just connected the new electrode and place the assy, in the burner.
Then just connected the new electrode and place the assy, in the burner.
Parts Used:
-
Billy from Martinsville, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
22 of 35 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken ignitor insulation; repeated sparking after burner lit
Disconnected gas & electric connections; lifted unit out of countertop onto padded table upside down. Unscrewed ~16 sheet metal screws for access. Removed bad ignitor by driving off retaining clip. Had to remove burner (3 screws) for access to install retaining clip on new ignitor. Reassembled, reinstalled. Works like new!
Parts Used:
-
Joe from San Bruno, CA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Wrench (Adjustable)
15 of 21 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!