Models
>
GW395LEGZ1
GW395LEGZ1 Whirlpool Range - Overview
Sections of the GW395LEGZ1
[Viewing 7 of 7]
Keep searches simple, eg. "belt" or "pump".
Light Bulb - 40W
PartSelect #: PS884734
Manufacturer #: 8009
This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these replacement bulbs are mos...
$11.73
In Stock
Range Inner Door Glass
PartSelect #: PS11747420
Manufacturer #: WP9781593
This inner door glass is used in ranges. It creates a transparent heat barrier inside your oven door. For this installment, the only tool needed is a #2 Phillips screwdriver. To repair, first remove t...
$98.21
In Stock
Screw - 10-16 x 1
PartSelect #: PS11741409
Manufacturer #: WP3387230
This screw is sold individually.
$7.95
In Stock
Grate Kit
PartSelect #: PS11754863
Manufacturer #: WPW10447925
This kit includes 4 black burner grates.
$264.57
In Stock
Touch-Up Paint - White
PartSelect #: PS385132
Manufacturer #: 72017
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
$8.00
In Stock
Temperature Sensor
PartSelect #: PS388521
Manufacturer #: 8053344
This temperature sensor is used with self cleaning ovens. Its 1000 ohm resistance increases with temperature. This sensor has male leads and comes with ceramic wire nuts.
No Longer Available
2 Piece Broiler Pan
PartSelect #: PS971245
Manufacturer #: 4396923
This is cookware designed for use in your range or oven. It is a two-piece dish that is used to grill or cook food while the broil function is on, meaning it can withstand high temperatures. This set ...
$37.51
In Stock
Light Gasket
PartSelect #: PS11740863
Manufacturer #: WP3184533
This part creates a seal around the light lens and bulb.
$11.14
In Stock
Cooktop Cleaner
PartSelect #: PS3492527
Manufacturer #: W10355051
This bottle of non-abrasive cooktop cleaner breaks down and gets rid of the hardest baked-on stains and residue without causing any harm to your appliance. The bottle is 10 oz and does not require a l...
$17.76
In Stock
Oven Igniter
PartSelect #: PS11747136
Manufacturer #: WP9753108
This part is used to light the oven for the bake or broil. Be very careful to not touch the black element part of this igniter as it is very fragile.
$112.35
In Stock
SOCKT-LITE
PartSelect #: PS16730838
Manufacturer #: W11594027
The light socket on your electric range connects the power source to the light bulb. If your oven light is malfunctioning, you may need to replace the light socket. The light socket is located in the ...
$59.64
In Stock
Rear Leveling Leg
PartSelect #: PS11748094
Manufacturer #: WPW10058460
Sold individually.
$11.06
In Stock
Questions And Answers for GW395LEGZ1
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the GW395LEGZ1
[Viewing 10 of 10]Little to no heat when baking
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Oven is too hot
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Little to no heat when broiling
Fixed by
these parts
these parts
Show All
Gas smell
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
F3 Error message
Two screws remove the front of the sensor (put a pan under the sensor to catch the screws), One nut removes the rear cover to access the rear of the sensor. Separating the two halves of wiring harness takes a little dexterity. BIG TIP! Tie a string to the back of the sensor wire and pull the sensor out from the front making sure the strin
... Read more
g still shows thru the back. If you don't you have a 15 minute job trying to fish the wires at an angle thru the insulation (a very frustrating task). Untie the string from the old and tie it securely to the new. Pull the string from the back and Voila! your new sensor can be plugged in or wirer nutted to the old connection on the back of the stove. Replace the nut and the two screws and you're done!
Read less
Parts Used:
-
Charles from Brecksville, OH
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
157 of 198 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Inside door glass broke
I removed the oven door by lifting it off with the hinges. Disassembled the door parts one at time making sure I remember where I removed the screws until I am able to get to the broken glass. The most difficult part is making sure that the insulation strip & the gasket stayed in place after I replaced the broken glass & doing the reverse
... Read more
process of installing the parts together. Relatively easy process as long as you remember where the parts go. When in doubt, I had to refer to the pictorial of the disassembled door shown on your website.
Read less
Parts Used:
-
MANNY from LIVERMORE, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
132 of 147 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven stopped working/Slow to ignite
Although the ignitors glowed brilliant yellow I learned from an expert there are 2 fail modes. 1. that they break and don't glow well enough to ignite the gas or 2. they get resistive over the years and do not pass enough current to open the valve. This is important to know because the current passes through the ignitor before it gets t
... Read more
o the valve. If the ignitor resists too much then the valve never gets enough power to open. As evidence you get slow ignitions until one day it stops altogether.
There are 2 ignitors in this oven. one for the broiler and 1 for the oven. The broiler is exposed so easily removed. For the oven you need to remove the flame spreader cover and the flame spreader. Need a good screw driver for all the screws in the oven because they get corroded from the hostile environment and also the factory torques them in pretty good when new. It is hard to get leverage leaning into an oven without leaning on the oven door which could unhinge it. With a good screw driver and getting a good seat into the screw you can break it loose. Then some muscle power to get it out. 1 screw refused to come out all the way so I grabbed it with some pliers and pulled and twisted it out. A trick I learned from my days as a mechanic is to use valve lapping compound on the screw driver. The diamond dust bites into the screw for a grip on those really bad ones.
The last tricky part is you have to remove the back cover on the oven, unplug the wires and pull the ignitor out through the oven. When you see the wires in the back you will see insulation packing.
Hint: If your smart you will tie a string to the wires before you pull it though so it is easier to pull the new ignitor wires back the same way. Else you need to use a stick to feel your way through the insulation packing to find the wires.
Hardest part of this job is undoing the screws. The rest is easy.
There are 2 ignitors in this oven. one for the broiler and 1 for the oven. The broiler is exposed so easily removed. For the oven you need to remove the flame spreader cover and the flame spreader. Need a good screw driver for all the screws in the oven because they get corroded from the hostile environment and also the factory torques them in pretty good when new. It is hard to get leverage leaning into an oven without leaning on the oven door which could unhinge it. With a good screw driver and getting a good seat into the screw you can break it loose. Then some muscle power to get it out. 1 screw refused to come out all the way so I grabbed it with some pliers and pulled and twisted it out. A trick I learned from my days as a mechanic is to use valve lapping compound on the screw driver. The diamond dust bites into the screw for a grip on those really bad ones.
The last tricky part is you have to remove the back cover on the oven, unplug the wires and pull the ignitor out through the oven. When you see the wires in the back you will see insulation packing.
Hint: If your smart you will tie a string to the wires before you pull it though so it is easier to pull the new ignitor wires back the same way. Else you need to use a stick to feel your way through the insulation packing to find the wires.
Hardest part of this job is undoing the screws. The rest is easy.
Read less
Parts Used:
-
John from Chicago, IL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Wrench set
58 of 63 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!