Models
>
CWG3020AAB
CWG3020AAB Maytag Wall Oven - Overview
Sections of the CWG3020AAB
[Viewing 7 of 7]
Keep searches simple, eg. "belt" or "pump".
Light Bulb - 40W
PartSelect #: PS884734
Manufacturer #: 8009
This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these replacement bulbs are mos...
$11.73
In Stock
Flat Style Oven Igniter Kit
PartSelect #: PS1573892
Manufacturer #: 12400035
The flat style oven igniter kit is used in gas ovens and ranges. It is what provides the heat needed to open the gas valve, and it ignites fuel for the burner assembly. This part can be used for both ...
$57.79
In Stock
Frame Screw
PartSelect #: PS11743908
Manufacturer #: WP7101P126-60
Sold Individually.
$7.76
In Stock
Door Seal - Top
PartSelect #: PS11743943
Manufacturer #: WP7212P006-60
This oven door seal creates a protective seal around an oven door to prevent heat from running out of a closed oven and keeps room air from entering the oven. This part is 17.5 inches long and made o...
$71.04
In Stock
Twist-Style Clock Knob
PartSelect #: PS1655662
Manufacturer #: 7711P172-60
Sold individually.
No Longer Available
Door Side Seal
PartSelect #: PS11743946
Manufacturer #: WP7212P015-60
Sold individually. Order quantity required.
$62.20
In Stock
Nut
PartSelect #: PS1722352
Manufacturer #: M0282009
This part is sold individually. This nut can be found in various appliances including a dishwasher, air conditioner, washer, dryer, range/cooktop, oven, freezer, range hood, and refrigerator. There is...
$14.09
Special Order
Capillary Clip
PartSelect #: PS2078936
Manufacturer #: 7112P053-60
This capillary tube clip is just under an inch long. It is made of metal.
No Longer Available
Dryer Screw
PartSelect #: PS11741528
Manufacturer #: WP3400094
Sold individually. (10-32 X 3/8)
$5.36
In Stock
Thermostat
PartSelect #: PS2089552
Manufacturer #: 7404P101-60
This temperature sensor detects the temperature within the oven cavity.
No Longer Available
Questions And Answers for CWG3020AAB
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the CWG3020AAB
[Viewing 7 of 7]Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Little to no heat when baking
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Gas smell
Fixed by
these parts
these parts
Show All
Little to no heat when broiling
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven would not work but the Broiler did
The oven had been working intermittently for a while and after repeated threats of starvation from my spouse I finally took a look even though it was summer and the grill was working fine. The Igniter would glow red when the oven was turned on but the gas would not flow to it no matter what the temperature setting. I searched online and f
... Read more
ound this site that explained it was possible for the igniter to glow but if it was not drawing the correct amperage (because its resistance was too high) then the main brain would not allow the gas valve to open. So I took a look at the broiler and it had the same igniter. I measure the resistance of both of them and the oven igniters resistance was higher (don't rememeber the reading) then I moved the Igniter from the broiler to the oven and the oven worked from there it was just a matter of ordering the part. End of story except for I am still doing all the cooking on the barbecue outside.
Read less
Parts Used:
-
James from Ferndale, MI
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers, Socket set
337 of 371 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven would'nt light
In most cases if your oven won't light or takes a long time to light you may have a bad igniter even if it glows. To check the igniter use a voltmeter to check for 120 A/C volts going to the igniter and3.5 A/C volts going between the ingniter and the gas valve. My bad ingniter glowed but had only only 3.0 A/C volts going to the gas valve
... Read more
for the oven. The new igniter took only 45 minutes to install and supply's 3.6 A/C volts to the gas valve and the oven works fine.
Read less
Parts Used:
-
Charles from Charlestown, RI
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
130 of 141 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven failed to light
My son replaced the broiler igniter this spring, so I had a clue as to what was required. This was even easier and since I had back surgery recently & my husband was out of town that was a giant plus!
I unplugged the oven, removed the oven door, found the release latch and removed the oven floor. I then removed the 2 screws ... Read more that held the igniter in place (I received this stove used and the igniter had evidently been replaced before as it was the same shorter version included in the kit). I pulled the igniter out then removed some insulation and tugged the connector out of the oven floor. I disconnected the igniter and plugged the new one in. I then replaced the connector in the floor, attached the igniter with the screws, replaced the insulation and did a test run (plugged in the oven & turned it on). That was successful so I put the floor back in and put the door back on.
Ta-Dah!
I unplugged the oven, removed the oven door, found the release latch and removed the oven floor. I then removed the 2 screws ... Read more that held the igniter in place (I received this stove used and the igniter had evidently been replaced before as it was the same shorter version included in the kit). I pulled the igniter out then removed some insulation and tugged the connector out of the oven floor. I disconnected the igniter and plugged the new one in. I then replaced the connector in the floor, attached the igniter with the screws, replaced the insulation and did a test run (plugged in the oven & turned it on). That was successful so I put the floor back in and put the door back on.
Ta-Dah!
Read less
Parts Used:
-
Beryl from Dawsonville, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
69 of 74 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!