Models
>
CSG5600BAL
CSG5600BAL Maytag Cooktop - Overview
Sections of the CSG5600BAL
[Viewing 1 of 1]Keep searches simple, eg. "belt" or "pump".
Screw
PartSelect #: PS12349731
Manufacturer #: W11233072
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$20.79
In Stock
Spark Module - Surface Burners
PartSelect #: PS2003170
Manufacturer #: 12001596
This part may differ in appearance, but functions same as original part. : This part sends enough current to the igniter to create a spark to the bottom of the burner cap.
$61.76
In Stock
Burner Spark Ignition Switch
PartSelect #: PS11744485
Manufacturer #: WP7403P190-60
Sold individually.
$71.04
In Stock
Pressure Regulator
PartSelect #: PS11744587
Manufacturer #: WP7510P083-60
This valve automatically cuts off the flow of gas at a certain pressure.
No Longer Available
Questions And Answers for CSG5600BAL
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the CSG5600BAL
[Viewing 3 of 3]Will Not Start
Fixed by
these parts
these parts
Show All
Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
No spark at top burners, first one then eventually all 4.
Most of the repair time was spent researching the problem online, locating the spark module inside the range, and selecting the part online. Installation was easy. Key troubleshooting info for me was, if there is no clicking, the spark unit is probably worn-out. I traced the ignition wires from the burners down to the spark module, locate
... Read more
d inside a 2x3" metal housing next to the bottom drawer. I removed 2 screws and out it came. The replacement unit pictured on the PartSelect site was not identical to the original but had the same number of contacts. I ordered the part and it arrived a few days later. The old connectors slipped easily onto the new pins, and I screwed the new unit into the range using the new metal housing. All 4 burners now spark up quickly, and we saved at least $100 on a service call. It was well worth the time and effort -- thanks!
Read less
Parts Used:
-
jonathan from Bryson City, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
32 of 37 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burners would not ignite
Pulled the stove out from the wall. Removed the left side of the stove. Removed the wires from the old igniter. Modified four of the wire ends with the proper size spade connectors (supplied with the new part). Reinstalled the wires onto the new part. Tested the burners. Reinstalled the stove side. Moved the stove back into position.
Parts Used:
-
Craig from Sequim, WA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
18 of 22 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Igniters were flaky on 2 burners and almost dead on 2
The part didn't come with installation instructions specific to any stove/oven so I went by a previous testimony on this website and pulled out the stove, and started to remove the side panel to get access. Well turns out I could have done the whole repair in place because on my Maytag the igniter source is accessible by removing the uti
... Read more
lity drawer and it's mounted on a small galvanized steel panel at the left side which hides the part directly. The existing spade connectors were the right size for me but I did have to crimp them tighter (which was perhaps part of the initial problem). After installation, the spark is much more powerful and all burners lit first couple "clicks".
Read less
Parts Used:
-
Matt from Craig, CO
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
7 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!