Models
>
CCGP2720P
CCGP2720P Jenn-Air Cooktop - Overview
Models starting with CCGP2720P
Click on the best match to narrow your results.
Keep searches simple, eg. "belt" or "pump".
Screw, 8/18 x 3/8
PartSelect #: PS11746840
Manufacturer #: WP90767
This screw is sold individually.
$5.42
In Stock
Gas Valve Knob
PartSelect #: PS11743848
Manufacturer #: WP71001057
This gas valve knob measures approximately 2 12 inches in diameter. It is a black knob that has white lettering aroud its perimeter denoting the different temperature levels: low, medium, high, etc. T...
$32.40
In Stock
Screw
PartSelect #: PS12349731
Manufacturer #: W11233072
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$20.79
In Stock
Spark Igniter
PartSelect #: PS11744544
Manufacturer #: WP7432P109-60
This part creates the spark that lights the gas and starts the burners.
$52.81
On Order
Glass Grease Collecting Jar
PartSelect #: PS11757591
Manufacturer #: WPY707869
This jar is a little over five inches long. It is made of glass and is used for collecting the grease drippings of gas ranges.
$45.50
In Stock
Rivet
PartSelect #: PS11738861
Manufacturer #: WP210720
This rivet is an inch and a half long. It is used for many washing machines, microwaves, refrigerators, dryers, and ranges. Use of this rivet requires a rivet tool.
$14.09
On Order
Mounting Nut
PartSelect #: PS11743922
Manufacturer #: WP7103P178-60
Sold individually.
$7.59
In Stock
Drain Jar Lid
PartSelect #: PS11742863
Manufacturer #: WP5700M611-60
This grease jar lid is used for some of Maytag/Jenn-Air's brands of ranges and cooktops. This lid is not quite an inch high and is three inches in diameter.
No Longer Available
Surface Burner Cap - Black - Large
PartSelect #: PS11744561
Manufacturer #: WP7504P157-60
This part helps the flame to spread for even heat. Also protects your burner head from spills.
No Longer Available
Indicator Light Lens
PartSelect #: PS11744689
Manufacturer #: WP7730P011-60
Sold individually.
$8.69
In Stock
Palnut
PartSelect #: PS2365913
Manufacturer #: 7103P166-60
This palnut is designed for use in cooktops, ranges, wall ovens, dehumidifiers, and range hoods. The palnut is screwed onto a bolt on top of an ordinary nut, and locks the nut in place when the nut is...
$16.17
In Stock
Common Symptoms of models starting with CCGP2720P
[Viewing 2 of 2]Will Not Start
Fixed by
these parts
these parts
Show All
Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Burners kept clicking after ignited
This problem was driving me crazy for months. Of course, after I bought and installed the part and it still was not fixed I finally found a website that told me how to fix the clicking. The problem is that the removable head burners (#8 on the top assembly diagram) are not making good electrical contact with the base burners (#22). What I
... Read more
did was grab the head burners and grind them back and forth into the base burners with the weight on the heal of my hand. Steel wool or sandpaper would work too--you just want to clean the surfaces to restore electrical contact.
If you still want to know how to replace the spark module start by removing #24. This will allow the removal of #9 (after you take the knobs off). You may have to do some fiddling cause the rubber gasket is sticky. Next there are 2 obvious regular screws for #14 and 2 not so obvious star screws in the space where the burner valves are. After #14 is off there are 2 screws on the spark module to be removed and one that you can't loosen that is in a slot. You wriggle the module out of that one.
If you still want to know how to replace the spark module start by removing #24. This will allow the removal of #9 (after you take the knobs off). You may have to do some fiddling cause the rubber gasket is sticky. Next there are 2 obvious regular screws for #14 and 2 not so obvious star screws in the space where the burner valves are. After #14 is off there are 2 screws on the spark module to be removed and one that you can't loosen that is in a slot. You wriggle the module out of that one.
Read less
Parts Used:
-
Robert from Ranchos de Taos, NM
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
27 of 29 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
would not stop igniting even after fire was on
unplugged unit from wall, disconnected gas line, and untaped the vent. disconnect the control knobs and unplugged and removed the control unit from the main unit. pulled the main unit out from the countertop and set it on a table. disconnect the burners and spark iginiters from the main unit. undo screws holding chrome brackets and stove
... Read more
base, to access iginiter. disconnect wiring from igniter and the one screw, replace iginiter. reverse everything to re-install
Read less
Parts Used:
-
Bill from Pearland, TX
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Wrench set
19 of 29 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
stove top gas burner ignitor only flicks but does not light burner
If you have a burner that begins to constantly flick without lighting, and/or flicks while you are lighting another burner, it is likely time to order a new ignitor. Once received, we first lifted the burner support rack, then the burner cap, then unscrewed the nut holding the metal bracket that holds the ignitor in place (years ago we h
... Read more
ad to "soak" the nut with a loosening spray prior to being able to unscrew it, so since then we do not tighten the nuts too tightly so that each nut is easy to unscrew by hand or with pliers if necessary). The previous steps allow one to lift the burner ignitor up and out of its resting hole. It will be connected to the electric wiring via a plastic connector. All one has to do is pull the wiring away from the ignitor and then push it up into the new ignitor. The plastic connector protects you from touching the live ends of the wiring. Voila! The burner lighted successfully.
Read less
Parts Used:
-
Marlene from Dana Point, CA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
12 of 15 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!