The lid hinge on your washer is connected to the lid and allows it to open and close. If you find you cannot open or close the lid to your washing machine properly, you may need to replace the lid hin...
$11.18
In Stock
Order within the next 5 hrs and your part ships today!
This lid hinge pin allows a washing machine lid to pivot open and closed properly. The hinge pin may need to be replaced if the lid will not open or will not close. The part is white and made of plast...
$22.28
In Stock
Order within the next 5 hrs and your part ships today!
The snubber ring is a piece that is specific to your washing machine. The function of the snubber ring is to reduce noise and vibrations within your washer. It fits in between the leg and the dome ass...
$13.11
In Stock
Order within the next 5 hrs and your part ships today!
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. If your machine is not draining properly or if it is noisy and s...
$120.13
In Stock
Order within the next 5 hrs and your part ships today!
This transmission pulley and bearing kit, also known as thrust bearing kit or washer pulley and bearing kit, includes the pulley, washer, thrust bearing, two upper race washers, and one lower race was...
$69.83
In Stock
Order within the next 5 hrs and your part ships today!
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
$11.80
In Stock
Order within the next 5 hrs and your part ships today!
This package contains a new set of six springs. The suspension springs in your washer connect to the bottom of tub, and help to hold it in place. If your washer tub shakes, or moves around a lot durin...
$68.55
In Stock
Order within the next 5 hrs and your part ships today!
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
$11.10
In Stock
Order within the next 5 hrs and your part ships today!
Hoses are the most likely cause of clothes washer leaks. This tub-to-pump hose carries the water from the tub to the drain pump. If you notice that your tub is leaking during the wash cycle, check the...
$28.67
In Stock
Order within the next 5 hrs and your part ships today!
I used a flat screw driver to push in on the releases so I could raise the top of the machine. I then used a torx tool to remove both parts of the hinge, and then used a #2 phillips screw driver, on the new screws I'd also ordered, to re-attach both of the hinge parts. Every thing went just as anticipated.
1)Start with empty washing machine. 2)Disconnect Hot, Cold, Power and Drain lines 3)Move machine to open area, open top by popping 2 front retaining clips. 4)Remove Front panel, remove small clear water level hose at lower rear of tub. 5)Remove small Rear access panel, disconnect large tub drain hose from pump and drai
... Read moren into small container, about 4 cups of water will come out. 5)Remove the 6 suspension Springs. 6)Place two large towels next to washer and tip machine onto its side slowly. 7)Remove drive belt from bottom, and slide out wash tub assembly thru top opening, be Careful not to damage large Plastic drive pulley on bottom of tub. 8)With tub upside-down, remove drive pully small plastic cover in center, remove E-Clip and remove pulley. 9)Slowly loosen snubber ring retaining bolts a few turns, DO NOT Remove, just loosen enough until snubber is free to move around. 10)Remove snubber ring by walking it around the retaining ring and install new snubber. 11) Clean machine cabinet and clean machine base where snubber touches with alcohol or Windex. 12) Reassemble in reverse order and Do Not Forget to reattach the small clear Water level sensing HOSE to the tub before closing the top. 13)Place Drive Belt onto the 2 small pulleys First, then slowly turn large pulley while walking belt onto it. 14)Reconnect machine to utilities and test run on small load to ensure no leaks and propper operation. 15)Enjoy Quiet free operation once again :)
back panel,belt two hoses,three screws, $100 dollars for the part!! pump is a molded part with a bearing insertion, is made in USA ! I'm guessing around 7 to 10 dollar manufacturing cost. I'm thinking that kind of mark-up is only exceded by the pharmacutical industry. I'm looking to buy a used machine for parts!!
.gif "SUPPLEMENTAL INFORMATION Diagram and Parts List for Admiral Washer")
