Admiral Refrigerator Ice Makers

Admiral Appliance Parts
Shop By Part Type

Popular Admiral Refrigerator Ice Makers

Your Price
$130.33
  On Order
Replacement Ice Maker
★★★★★
★★★★★
(111)
PartSelect Number PS2121513
Manufacturer Part Number D7824706Q
This ice maker (Ice Maker Assembly, Refrigerator Ice Maker) produces ice cubes that are ejected into the storage bucket. It is located in the freezer section of your appliance, mounted on the freezer wall. The ice maker can break from normal wear and accidental damage. If this happens, your refrigerator may no longer make ice cubes, or may not make enough cubes, and the part should be replaced. This model measures approximately 11 inches long and 5 inches wide. It’s constructed of plastic and metal, and comes in black/white/silver. This assembly includes the ice mold and the control device.
Fixes these symptoms
  • Ice maker dispenses too little ice
  • Ice maker dispenses too much ice
  • Ice maker not making ice
  • See more...
Installation Instructions
Bernie from Diamond Bar, CA
Icemaker producing few or no cubes and often leaving "kling-ons" on ice tray
Interior surface of ice tray felt rough & flaky (coating deteriorated) so cubes would not release.
Unplug appliance.
Remove timer cover by hand pressure @ edge.
Remove single attachment screw & bracket at lower front of icemaker.
Disconnect wiring harness from socket @ rear of compartment.
Tricky part was determining what type of connection held the other two attachment points along the long edge of the icemaker. I did not have repair manual or useful drawing but looked @ PartsDirect pic of side brackets & used a small mirror to confirm that mine were also some sort of "snap in" attachment.
Remove icemaker unit by pushing upward and outward on the unit. I takes a good bit of pressure and will pop loose, but be careful not to break attachment bracket from freezer wall.
Scavenge shut off bar and wiring harness from old icemaker once you have it out & attach to new one before installing it back in freezer.
Again, you might find a mirror useful to align those pesky snap-in brackets with the new unit.
Since you probably kept your freezer running while waiting for the part, the plastic snap-ins will be cold and brittle. I warmed them up first by applying a dampened cloth heated in the microwave to make them a little more pliable.
A good push of the new unit towards the snap-ins along with some upward force will get it stable.
Reattach the metal screw in bracket & connect the wiring harness to rear plug... and don't forget to plug the whole thing back in.
It will take awhile for the first batch of cubes dump as the timer may need to cycle completely around to get to the fill cycle... be patient.
Dump the first couple of batches of cubes just to make sure you're free of any residue.
Read more...
Your Price
$29.28
  In Stock
Water Fill Cup and Bearing
★★★★★
★★★★★
(9)
PartSelect Number PS11743318
Manufacturer Part Number WP628356
This refrigerator ice maker fill cup dispenses the water into the ice cube mold during the fill cycle. Replacing the water fill cup is a possible solution if you notice that the ice maker is leaking, or not making/dispensing ice. If you notice the fill cup has been damaged or cracked; replace the part straight away. This water fill cup is a genuine OEM part and will fit most refrigerators, but check the list of compatible brands to make sure yours is included before purchasing.
Fixes these symptoms
  • Ice maker dispenses too much ice
  • Ice maker not making ice
  • Ice maker won’t dispense ice
  • See more...
Installation Instructions
David from Chester, CA
The Bearing Cup Assembly was broken and ice would jamb against it during the ice making cycle.
I removed the ice maker from the refrigerator, by removing one screw on the underside bracket and loosening the two screws at the top side, then lifting the ice maker off the loosened screws. I then unplugged the electrical harness that supplies power from the refrigerator to the ice maker. I then disassembled the ice maker by removing the front cover which is snapped in place, then removing two recessed screws at the front. I removed the broken part, I then reassembled the ice maker with the new part. I replaced the two recessed screws at the front and snapped on the cover. Then I reinstalled the ice maker in the refrigator by plugging in the harness, slipping the ice maker over the loosened screws in the refrigerator and replacing the screw that was removed from the underside bracket. Tightening all the screws completed the project. Read more...
Your Price
$20.54
  On Order
Ice Maker Helix End Cap - white
★★★★★
★★★★★
(8)
PartSelect Number PS11747838
Manufacturer Part Number WPD7749401
This helix end cap is almost four inches in diameter. It is all white in color and is made of plastic. This end cap is used in a refrigerator's icemaker.
Fixes these symptoms
  • Ice maker not making ice
  • Ice maker won’t dispense ice
  • See more...
Installation Instructions
Todd from Lancaster, PA
Ice maker would not turn allowing the ice to come out the dispenser. The ice bucket was also cracked from kids (ok and parents) getting frustrated and shaking the ice bucket!
Piece of cake!

Removed the old ice bucket which was cracked and ice would not dispense. The Helix Cap also looked worn which is why I ordered both parts. (Probably if not for the shaking of the ice bucket the Helix cap would have been the only part required. We ended up cracking the ice bucket) Removed the four hex screws from the auger system on the old ice bucket with a socket wrench. Removed the old Helix end cap from the auger system and replaced with the new. Literally just slips on the auger. Reinstalled auger system back onto the new ice bucket. Total time not even five minutes.

Working great! Probably saved $ 75.00 - $ 100.00 on a service call. Half of a wrench on skill level needed (One=Low skill level/ Five=High skill level)

Great response & delivery from Parts Select!
Definitely recommend highly.

Todd
Lancaster-PA
Read more...
Your Price
$100.31
  On Order
Ice Bucket
★★★★★
★★★★★
(4)
PartSelect Number PS11743653
Manufacturer Part Number WP67005959
Bucket only.
Fixes these symptoms
  • Ice maker not making ice
  • Ice maker won’t dispense ice
  • See more...
Installation Instructions
Stanley from Cortland, OH
Ice maker was leaking water and causing ice globs in ice bucket.
Parts were available at the locat applicance store, but the cost was 20-25% higher than ordering through Parts Select (including shipping) + it was delivered in 3 days right to the house.

Removing and replacing the ice maker was fairly straight forward. Tight quarters to work in, but managable.

1. With the freezer turned off, uplug the ice maker power cable at the back of the freezer.
2. Remove the four phillips head screws and ice bucket rail to the side of the freezer. I found it was easier to re-install the new ice maker with the rail clear off.
3. Loosen the two upper hex head screws holding the ice maker (requires a nut driver).
4. Lift the ice maker up and off of the upper screws.
5. With the ice maker out of the freezer, remove the power cable from the old ice maker and re-install on the new ice maker. At this point, both the front cover and the on/off lift bar can be transfered from the old ice maker to the new one.
6. Slip the new ice maker down over the two upper screws making sure the lower mounting tab is behind the ice bucket rail. Make sure the hole on lower mounting tab lines up with screw hole.
7. Re-install the ice bucket rail and tighten all screws. Make sure the water supply tube is lined up correctly feeding into the ice maker.
8. Re-connect ice maker power cable at the back of freezer and turn freezer back on.

It took about 4 hours for the first ice to generate. It cycled normally after that. No more leaks or ice globs in the ice bucket.
Read more...
Your Price
$218.98
  On Order
Ice Maker Auger and Crusher Blade Assembly
★★★★★
★★★★★
(6)
PartSelect Number PS11738609
Manufacturer Part Number WP12740302
This is the replacement ice maker auger and crusher blade assembly for your refrigerator. It is approximately 15 inches long and 7 inches wide. The ice maker auger sits within the ice maker assembly and rotates to push the ice from ice container into the dispenser chute. If your ice maker bucket is full, but ice is not being dispensed, it is an indication that the auger is damaged. Be sure to disconnect power from the refrigerator before you repair the auger. This part is sold individually and is an authentic OEM part sourced directly from the manufacturer.
Fixes these symptoms
  • Ice maker not making ice
  • Ice maker won’t dispense ice
  • See more...
Installation Instructions
James from Robinson, TX
Ice Dispenser had jammed up and become inoperative
The parts discription was a bit vague and I wasn't sure exactly what I was ordering, but I received everything I needed and it works fine. The combination screw conveyor/ice crusher came in one piece. The ice cube bin is a plastic assembly that snaps apart. I used a wide blade screw driver carefully to facilitate assembly/disassembly. Once you have it apart the old converyor slips out and the new one slides in. Do not remove the two screws that hold the new assembly together. You need a phillips scredriver to take out two of the screws from the old assembly and put in the new one. That is, there are four screws and you need to trasfer two of them. Everything now works fine. Read more...
Your Price
$5.67
  In Stock
Ice Maker Front Cover
★★★★★
★★★★★
(2)
PartSelect Number PS11752097
Manufacturer Part Number WPW10289690
Your Price
$84.54
  In Stock
Ice Bucket
★★★★★
★★★★★
(3)
PartSelect Number PS11743447
Manufacturer Part Number WP67001255
The ice bucket in your freezer catches and holds the ice when it is released by the icemaker. If your ice bucket is cracked or damaged, you may need to replace it to prevent a potential leak. This part is made of white plastic and is sold individually. This ice bucket is approximately 15 inches long by 12 inches wide. Many of our customers have rated this repair as very easy. To complete this repair, simply remove the old ice bucket and replace it with the new one. Be sure to remove any broken pieces of the old ice bucket before replacing it.
Installation Instructions
ROBERT from FLAGLER BEACH, FL
ice maker stopped making ice
I loosened the two top screws, removed the bottom screw, lifted up on ice maker and slid it off, unplugged the wire from refrig. I transfered the wire to the new icemaker, pluged it back in, placed it on the two screws, installed lower screw, tighten top screws. Total time spent less than 15 minutes. The ice maker cost $125.00 with freight. Sears wanted $374.00 Read more...
Your Price
$29.76
  In Stock
Crushed Ice Wheel
★★★★★
★★★★★
(3)
PartSelect Number PS11743477
Manufacturer Part Number WP67002052
This crushed ice wheel is five inches in diameter. It is beige in color and is made of plastic.
Fixes these symptoms
Installation Instructions
Fred from Olathe, KS
Crushed Ice Wheel began to fragment
This is a side-by-side refrigerator. The crushed ice wheel is part of the icemaker bin auger, and it began to fragment, popping pieces of plastic into the ice dispenser and on into our drinks. The manuf. manual had nothing about parts in it, so GREAT thanks to Partselect for their website!!! Now, to dismantle the bin and auger is simple on this design: remove the bin from the freezer and allow it to defrost and dry; there are two small phillips-head screws on the front underside of the bin, holding the front panel in place - remove these screws and pop the front cover off; you'll then see two small phillips-head screws holding the auger-cap in place - remove these and pull the auger cap out, along with the auger; using a small pliers, remove the nut from the auger at the auger-cap, then slide the auger-cap off; at this point you just start removing washers, blades, etc, from the auger - MAKING SURE YOU KEEP THEM IN ORDER - until you reach the crushed ice wheel; separate the wheel from its metal brace, slide the wheel off and replace it; gradually replace all the other parts in order, cleaning them as you go, and simply put everything back together. It helps to keep the exploded parts diagram at hand - available on the Partselect website. It was a snap. The ordering process was simply and the part was delivered to my door on the second day after ordering. Read more...
Your Price
$28.81
  On Order
Ice Bin Drive Ring
★★★★★
★★★★★
(1)
PartSelect Number PS11743163
Manufacturer Part Number WP61003336
This drive ring is three inches in diameter. It is all white in color and is made of plastic. This ring is used with a refrigeraor's icemaker assembly.
Fixes these symptoms
  • Ice maker not making ice
  • Ice maker won’t dispense ice
  • See more...
Installation Instructions
Robert from Groveport, OH
The drive ring broke which kept the bin from despensing ice.
First I removed the screws from the front of the ice bin which freed up the drive mechanism. I then removed the drice ring and replaced it with the part from Parts Select and then replaced the screws on the front. A very simple procedure.
The chill department door was an easy snap in replacement..

I would like to add that I was very pleased with Parts Select. Locating the parts I needed was very easy and I received them the next day. When The door first broke I was told I would have to replace
the whole assembly which I was not willing to do
at a quoted price of about $350.00. Needless to say I was very happy to locate Parts Select and was very pleased with everything. I have since told family and friends about Parts Select.
Read more...
Your Price
$16.71
  On Order
Ice Cube Tray
PartSelect Number PS11743133
Manufacturer Part Number WP61002140
This ice cube tray is located inside your refrigerator and is eleven inches long, with 48 molds. It comes in white and is made entirely from plastic. If your tray is broken, cracked, or damaged, replacing this part can solve the problem. Here are some ice cube tray tips to consider: the easiest way to release the cubes is by giving the tray a twisting motion from both sides. If that does not work, set it on your counter for a couple minutes until the tray warms up and it should work. Remember not to beat the tray, especially on a hard surface, to prevent damage. Refer to manual instructions provided by the manufacturer if needed.
Installation Instructions
Craig from Westminster, CA
cocktails running out of ice
filled both ice cube trays up with water and placed in the freezer.. within hours my ice oproduction was doubled! no more warm cocktails : ) Read more...

Related Parts