Admiral Dryer Seals and Gaskets | Replacement Parts & Accessories | PartSelect

Popular Admiral Dryer Seals and Gaskets

Rear Drum Felt Seal – Part Number: W10612022
Your Price
$41.01
Rear Drum Felt Seal
PartSelect Number PS8691753
Manufacturer Part Number W10612022
This seals Includes adhesive. This part helps seal the drum to prevent hot air from escaping.
Fixes these symptoms
Marks left on clothes
No heat or not enough heat
Noisy

See more...
Installation Instructions
Paul from Monmouth, IL says,

intermittant heat
First I shut off the gas supply and disconnected the dryer vent and unpluged the unit so you can access the rear of the dryer. Then I removed the rear cover. This is where you will find your thermosta...read more

Lint Trap Housing Seal – Part Number: WP339956
Your Price
$7.43
Lint Trap Housing Seal
PartSelect Number PS11741506
Manufacturer Part Number WP339956
This is foam seal for your dryer. It forms a seal to prevent air from escaping the rear of the dryer drum and the lint duct. This model comes with adhesive backing and is located in between the lint chute and the bulkhead of your appliance. This foam seal is just over 28 inches long and under 1 inch wide. You may need to replace this part if your clothing is taking too long to dry, or if your dryer is not generating enough heat or no heat at all.
Fixes these symptoms
No heat or not enough heat
Noisy
Takes too long to dry

See more...
Installation Instructions
Eric from Fort Dodge, IA says,

dryer drum not turning and no air circulating
replaced motor and drum rear seal as well as idler wheels, the old rear drum seal was completly worn out, since I had it all apart, I replaced lint chute and trap seals and belt and tensioner. I spent...read more

Door Gasket – Part Number: W10861521
Your Price
$42.97
Door Gasket
PartSelect Number PS11731610
Manufacturer Part Number W10861521
This door seal does not include the adhesive glue.
Fixes these symptoms
No heat or not enough heat
Takes too long to dry


Installation Instructions
Manolak from MURFREESBORO, TN says,

Door Gasket tore out
Put high temperature glue on first, then put door gasket over the high temperature glue and then let it set for 24 hours. It worked fine.......read more

Dryer Drum Seal with Adhesive – Part Number: 280114
Your Price
$43.16
Dryer Drum Seal with Adhesive
PartSelect Number PS970088
Manufacturer Part Number 280114
This drum seal with a silicone rubber adhesive is used in dryers. This part seals the drum to make sure air does not escape from the dryer. If your dryer is making loud noises, is not producing enough heat, or no heat at all, or there are marks left on your clothes, replacing the seal on your dryer can solve the problem. The tools needed for this installation project are: 1/4 inch nut driver, Phillips screwdriver, small flat blade screwdriver, and putty knife. Remember to unplug your dryer from the power source before beginning this installation project. Refer to the manual provided by the manufacturer for installation instructions.
Fixes these symptoms
Marks left on clothes
No heat or not enough heat
Noisy

See more...
Installation Instructions
Jerry from Everett, WA says,

Rear tub seal failure
I removed the top cover and then the back cover, released the belt tensioner and removed the drive belt. Then slid the tub out of the unit and onto the back dack. Sanded the remnents of the old seal o...read more

Cylinder Felt Seal – Part Number: WP37001132
Your Price
$24.03
Cylinder Felt Seal
PartSelect Number PS11741917
Manufacturer Part Number WP37001132
This cylinder felt seal is used in dryers and is located between the back of the drum and the rear dryer panel. If your dryer is experiencing any of these symptoms, replacing the felt seal could solve your problem: squealing or banging noise, clothes are getting stuck between tub and felt pad, takes too long to dry, not heating enough or not heat at all, or does not tumble. The tools needed for this installation are a 5/16 nut driver and a putty knife. Make sure to unplug the dryer from the power source before beginning this project. Refer to the manual provided by the manufacturer for further instructions.
Fixes these symptoms
Marks left on clothes
No heat or not enough heat
Noisy

See more...
Installation Instructions
Tim from South Glens Falls, NY says,

The Felt Gasket between drum and door ripped, vent manifold from Dryer to fan and lint screen broken
I pulled the bottom panel and the door panel to replace the manifold and felt gasket around the drum. I removed old gasket very easily, it peeled right off. I use brake cleaning fluid (Spray Can fro...read more

Seal and Bearing – Part Number: W11035878
Your Price
$43.28
Seal and Bearing
PartSelect Number PS11773177
Manufacturer Part Number W11035878
This front panel seal kit doesn't include the plastic retainers, reuse the old retainers. No glue is needed, the seal stretches to fit.
Fixes these symptoms
Marks left on clothes
Noisy
Takes too long to dry

See more...
Installation Instructions
Stephen from Springfield, MA says,

Dryer making loud squealing noise when running
The (front) bearing and seal are not metal parts but a fabric and and mesh like material. It is somewhat like a fabric belt made to hold up a pair of trousers. The belt sits in a channel that goes aro...read more

SEAL-DOOR – Part Number: W10906683
Your Price
$48.69
SEAL-DOOR
PartSelect Number PS11766744
Manufacturer Part Number W10906683
Fixes these symptoms
Takes too long to dry


Installation Instructions
alice from wickliffe, OH says,

seal came of dryer door
romoved from pkg. and fit it to the door. no tools needed. best of all the part came in 24 hrs and was fixed with out delay of waiting from a store that was out of our area. great costumer service!!...read more

Blower Housing Seal – Part Number: WP697770
Your Price
$6.43
Blower Housing Seal
PartSelect Number PS11743810
Manufacturer Part Number WP697770
This part seals between the blower housing and the blower housing cover.
Fixes these symptoms
No Symptoms for this part
Installation Instructions
Boonkham from SMYRNA, TN says,

Unit not spent
Just replaced part...read more

Seal, Outlet Housing – Part Number: WP697813
Your Price
$7.02
Seal, Outlet Housing
PartSelect Number PS11743812
Manufacturer Part Number WP697813
This lint chute seal, also known as a seal for outlet housing, is used for dryers. This part seals the lint chute to the blower housing in a dryer. It prevents air from leaking around the filter housing. If your seal is broken, damaged, or overused, it can allow lint to bypass the lint filter. In this case, replacing the seal can possibly solve the issues. The tool needed for this repair is a Phillips screwdriver. Refer to the manual provided by the manufacturer for further installation instructions and remember to unplug your dryer from the power source before beginning this repair project.
Fixes these symptoms
No Symptoms for this part
Installation Instructions
Dennis from PALM BCH GDNS, FL says,

Lint filter seal worn out
The part wasn’t for my machine. Unfortunaly I was not able to repair it. I was sent stripe of foam with an adhesive strip on the back. I needed a felt strip....read more

Rear Drum Seal with Adhesive – Part Number: 239087
Your Price
$56.93
Rear Drum Seal with Adhesive
PartSelect Number PS333333
Manufacturer Part Number 239087
Includes high temperature adhesive.
Fixes these symptoms
Marks left on clothes
Noisy
Takes too long to dry

See more...
Installation Instructions
Lauren from Mckinney, TX says,

The dryer was leaving rust marks on our clothes.
After my husband disassembled the cabinet and removed the drum, we used a putty knife to remove the old seal and carefully glued the new one in place. (A 2 man job to do it without leaking glue everyw...read more