Whirlpool Washer Valves

Find Your Part

Model number locator Need help finding your model number?
  • Search your model number to find:
  • Genuine OEM parts guaranteed to fit
  • Free manuals and guides
  • Repair instructions and videos
Whirlpool Appliance Parts
Shop By Part Type

Popular Whirlpool Washer Valves

Videos!
Your Price
$35.28
  In Stock
Whirlpool Washer Water Inlet Valve with Mounting Bracket
★★★★★
★★★★★
132 Reviews
PartSelect Number PS334646
Manufacturer Part Number 285805
The water inlet valve on your washing machine is used to fill the tub with cold, warm, or hot water for the wash and rinse cycles. This part could have either a blue or green-colored valve body. There are two ports for water to enter and this valve is compatible with a half-inch ID hose. It has two 3/4-11x1/2 NHT hose threads. You may have a faulty valve if your washer is leaking, has no hot or cold water, will not stop filling with water, will not fill with water, fills and drains at the same time, or is noisy. To confirm that the valve is faulty, unplug the washer when the symptom occurs. If the washer continues to fill, then the inlet valve is defective.
Fixes these symptoms
  • Leaking
  • No hot or cold water
  • Water Filling Issues
  • See more...
Installation Instructions
Don from Wyoming, MN
Washer stopped at rinse cycle
Removed the top and back panels. Replaced
compoments and reassembled.
Test run machine. Ran like new! Read more...
Videos!
Your Price
$70.56
  In Stock
Whirlpool Washer Water Inlet Valve
★★★★★
★★★★★
40 Reviews
PartSelect Number PS12349267
Manufacturer Part Number W11210459
This water inlet valve is for washers. The water inlet valve controls the water flow into the washer. Unplug the washer and shut off the water supply before installing this part. Wear work gloves to protect your hands.
Fixes these symptoms
  • Leaking
  • No hot or cold water
  • Water Filling Issues
  • See more...
Installation Instructions
Patricia from MURPHYSBORO, IL
Water would not fill the washer except for 4 inches.
Once we put in the new Water Inlet Valve, the auto sensor works now and I can wash any size load Read more...
Videos!
Your Price
$59.88
  In Stock
Whirlpool Washer Water Inlet Valve with Thermistor
★★★★★
★★★★★
35 Reviews
PartSelect Number PS11749042
Manufacturer Part Number WPW10144820
This part is used to help control and balance the water temperature flowing in to the washer tub.
Fixes these symptoms
  • Leaking
  • No hot or cold water
  • Water Filling Issues
  • See more...
Installation Instructions
Barb from Blackriver Falls, WI
fill valve bad
took back off then removed valve replaced with new one works good Read more...
Your Price
$92.13
  In Stock
Whirlpool Washer Water Inlet Valve
★★★★★
★★★★★
10 Reviews
PartSelect Number PS12349461
Manufacturer Part Number W11220230
This is a water inlet valve made for washing machines. This part is used to control the flow of water into the fill hose of the washing machine, to allow the washer to fill up with water. If your washing machine is not filling up with water properly, or if you are noticing leaks underneath your washing machine, the inlet valve has likely failed and you will likely need to replace it. This OEM inlet valve features two different inlets for hot and cold water but does not come with any other parts or accessories for installation. To replace this water inlet valve, you will need tools such as a screwdriver or wrench to gain access to it and remove it.
Fixes these symptoms
  • Leaking
  • No hot or cold water
  • Water Filling Issues
  • See more...
Installation Instructions
Kynrick from DENTON, TX
Water leaking at front left of washer especially after heavy loads
Disconnected water and unplugged. Took off top and control panel. Replaced water inlet valve with new one. Simple plug and play connections. It was easy to see the old valve was bad with rust and sediment collecting on hot side. Read more...
Your Price
$77.35
  In Stock
Whirlpool Washer Water Inlet Valve
★★★★★
★★★★★
20 Reviews
PartSelect Number PS11773194
Manufacturer Part Number W11038689
This is an inlet valve for various washing machines. Inlet valves are responsible for opening and closing as needed, to allow water to enter the washer during the washing cycle. This inlet valve features a hot and cold-water valve, as well as the necessary wire harness to easily plug it in. Since inlet valves are an electrically controlled solenoid valve, they can fail either due to electrical failure such a short, or after long, extended use. If your inlet valve fails, your washer will likely relay an error code, or it simply will not wash your clothes due to the lack of water, and the valves will need to be replaced. Replacing this valve will require a screwdriver and/or socket wrench, and some disassembly of your washer will be necessary. This inlet valve is an individually sold OEM part and does not come with any accessories or other parts.
Fixes these symptoms
Installation Instructions
melinda from HARROGATE, TN
Water would not stop flowing.
*be sure to turn water off, unplug machine, and unscrew the water hoses from the rear of the washer.
1. Removed screws from the back of the washer, just the top part where the controls are.
2. Removed the panel.
3. Use a putty knife or screw driver to pop off the top panel.
4. Remove the screws from the inlet valve.
5. Unplug the wires connecting the inlet valve to the washer.
6. Lift out the old inlet valve.
7. Replace with the new inlet valve.
8. Plug the new wires into the washer.
9. Replace the screws in the inlet valve.
10. Replace the top.
11. Replace the rear panel and screws.
12. Reconnect the water hoses, careful not to mix the hot and cold.
13. Plug the machine back in and you're finished! Read more...
Videos!
Your Price
$87.01
  In Stock
Whirlpool Washer Water Inlet and Valve Assembly
★★★★★
★★★★★
32 Reviews
PartSelect Number PS11757114
Manufacturer Part Number WPW10683603
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
Fixes these symptoms
Installation Instructions
Armand from WESTPORT, MA
Water inlet nozzle was stripped and leak
Remove the front panel and back panel unplug the part unscrewed the part and replace it with the new one Read more...
Videos!
Your Price
$81.60
  In Stock
Whirlpool Washer Water Inlet Valve
★★★★★
★★★★★
21 Reviews
PartSelect Number PS11745050
Manufacturer Part Number WP8182862
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
Fixes these symptoms
  • Leaking
  • No hot or cold water
  • Water Filling Issues
  • See more...
Installation Instructions
Jerry from Keenes, IL
washing machine giving f20 error code
removed washer top, checked supply hoses and inlet valve to make sure not clogged, replaced valve and while already there replaced flowmeter, reinstall top and hoses and checked machine operation, machine working fine and wife thinks i am her hero Read more...
Videos!
Your Price
$118.84
  In Stock
Whirlpool Washer Dual Cold Water Valve
★★★★★
★★★★★
11 Reviews
PartSelect Number PS11750469
Manufacturer Part Number WPW10212596
Water inlet valve controls the water flow into the washer. Fits some washers in the following series: Kenmore 110; Whirlpool CHW, WFW and YWFW; Maytag CHW, MHN, MHP, MHWE, MHWZ and YMHWE; Amana NFW and YNFW; and Inglis IFW and YIFW. Also fits some laundry centers in these series: Whirlpool CET and CGT; and Maytag MLE and MLG.
Fixes these symptoms
  • Does not dispense fabric softener or detergent
  • Leaking
  • No hot or cold water
  • See more...
Installation Instructions
Laura from ENGLEWOOD, CO
Washer would fill extremely slowly when on cold water wash resulting in long fill(LF) error code.
The washing machine would only run on the hot water cycle. When trying to use the warm or cold setting, the water would dribble into the drum and result in an LF error code(long fill). I watched a brief video on replacing the water inlet valve which made it really easy to repair. I first turned off the water, disconnected the hoses from the machine, and opened the top to access the valves. I then disconnected the wires from the valve, removed the water tubes, swapped out the valves and put everything back together. I am not experienced in repair but this was a very easy fix! We decided to replace the single hot water valve and the dual cold water valve since it's an older machine and it works like new again! Read more...
Your Price
$118.38
  In Stock
Whirlpool Washer Valve
★★★★★
★★★★★
3 Reviews
PartSelect Number PS11754698
Manufacturer Part Number WPW10435242
Fixes these symptoms
Videos!
Your Price
$152.28
  In Stock
Whirlpool Washer Water Inlet Valve
★★★★★
★★★★★
7 Reviews
PartSelect Number PS11731257
Manufacturer Part Number W10853723
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
Fixes these symptoms
Installation Instructions
Benjamin from FLINT HILL, VA
Cold water leaked into tub
Replaced water inlet valve. Parts select video was incorrect for my unit. There are no spring clips to be released using a putty knife. Rather remove the two screws in the back of the top, pull the top forward and up to get at hose connections to the valve. Hint, place a towel under the valve connections because after removed from the valve, the hoses will leak to the floor. I propped the top up with a stick. All the other stuff in the video is good. Unplug and turn water off, remove connectors from old valve etc. . I also removed the protective plate over the cabled that runs between the washer and the control panel located on the back of the washer. The will make the sliding of the top forward easier. Only one screw involved. Read more...

Related Whirlpool Washer Parts

Back to Top