Wall Oven Wire Plugs and Connectors

Videos!

Your Price

$16.24

Wall Oven Terminal Block Kit

★★★★★

37 Reviews

PartSelect Number PS470125

Manufacturer Part Number 5303935058

This part connects the wire harness to the surface element and is used for ranges. The kit includes interchangeable mounting brackets, ceramic wire nuts, heat shrink protective tubing, and wires. If your range/oven is having symptoms such as burner not heating, heating elements not working, burning smell, or if the oven is making a buzzing noise then this could be the solution. The tools needed to replace the kit are wire strippers, a heat gun or hair dryer, and #1 square heard screw driver. Refer to the installation/instructional video for further guidance to accurately replace the element.

Fixes these symptoms

Element will not heat
Oven not heating evenly
Will Not Start
See more...

Installation Instructions

Steven from Taylors, SC

rental property stove only had 2 working burners and bottom drawer off track

first i took out burners then i took out the screws of the termnal block bracket. i then raised the lid on the stoveand clipped the wires on all 4 of the terminal block kits.i then slipped the shrink wrap on wires and used the wire nuts to connect wires together then heated the shrink wrap. I then put screws back in terminal block brackets. I then put the burners on while looking under lid so i would know they were making good connections as this is a bad design from factory. if you pull out burners to clean them and they are not put back in right you dont have a good connection and that causes the terminal blocks to get hot and melt. thats what happened in my case.
As far as the drawer glides they just snap into place Read more...

Videos!

Your Price

$9.37

Wall Oven Main Terminal Block Kit

★★★★★

12 Reviews

PartSelect Number PS471605

Manufacturer Part Number 5304409888

Terminal block kits are also known as terminal boards, or terminal strips, and they are found in a wide variety of household appliances. Most often in ranges, wall ovens, and dryers. This kit attaches the power cord to the inner wiring of your appliance. If the terminal block is faulty, your appliance will not get the power it needs to operate properly. When removing the old block pay close attention to the wire placement, this will make installing your new part much easier. If you notice any of the wires or wire terminals are corroded or damaged they will also need to be replaced.

Fixes these symptoms

Element will not heat
Little to no heat when baking
Little to no heat when broiling
See more...

Installation Instructions

Timothy from Spring Valley, AL

Cord was not tightened enough by delivery crew.

PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools needed are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful. Read more...

Videos!

Your Price

$34.09

Wall Oven Terminal Block

★★★★★

17 Reviews

PartSelect Number PS11750972

Manufacturer Part Number WPW10245259

This part is for oven ranges, it connects individual wires and protects the device from electrical surges, voltages, and current. With this part, the house power is connected to the range wire harness. Some symptoms replacing the terminal block could be a solution for are little to no heat when baking, element will not heat and/or it will not start. This part will prevent loosening and will reduce damage caused by corrosion (by two different metals). Refer to the instructional diagram for further replacement guidance and exact placement. You must unplug the appliance before installing this part and wear gloves to protect your hands.

Fixes these symptoms

Element will not heat
Little to no heat when baking
Touchpad does not respond
See more...

Installation Instructions

Joseph from Decatur, GA

Burned terminal block and filter board

Removed and replaced above named parts, rewired.Be sure to tighten all nuts that secure wires. I believe this is what caused the problem. Read more...

Your Price

$50.24

Wall Oven Terminal Block Kit

★★★★★

4 Reviews

PartSelect Number PS2333392

Manufacturer Part Number 5303935271

Fixes these symptoms

Will Not Start
See more...

Your Price

$56.72

Wall Oven Terminal Block Kit

★★★★★

13 Reviews

PartSelect Number PS953027

Manufacturer Part Number WB17T10011

This part provides a way of connecting individual electrical wires and offers protection of the device from electrical surges (voltages and/or currents).

Fixes these symptoms

Element will not heat
Will Not Start
See more...

Installation Instructions

jonathan from willow springs, IL

terminal block melted

The existing terminal block on my Ge oven/Range had melted due to a loose wire causing sparking and starting the plastic casing of the terminal block on fire and melting it, Part select made the part easy to find and had it at my house in 2 days. All I had to do was remove six screws to take the back sheet metal cover off of the oven. Unscrew the terminal connections remove two mounting screws that held the terminal on to the oven body. This was a little trickier than it should have been because the melted plastic had reformed making it very hard to access the mounting screws. i then mounted the new piece and plugged the oven in, it took 15 minutes and was very easy. definitely saved me at-least a $100 for the service call i would have made if finding the part wasn't so convenient Read more...

Videos!

Your Price

$24.59

Wall Oven Main Power Terminal Block

PartSelect Number PS11745232

Manufacturer Part Number WP8203546

Sold individually.

Fixes these symptoms

Will Not Start
See more...

Installation Instructions

Frank from Silverhill, AL

lighting strike

replaced the suppressor and terminal block oven works Read more...

Your Price

$47.69

Wall Oven Cartridge Receptacle

PartSelect Number PS11757565

Manufacturer Part Number WPY702434

This cartridge receptacle is almost four inches long. It is white in color and is made of ceramic.

Fixes these symptoms

Element will not heat
See more...

Installation Instructions

Stephen from Andover, MA

Infinite switch ran more than one burner

Purchased 1 infinite switch and installed it on the left front burner. problem still there so I used the switch that I replaced on the rear burner and all was ok. The front switch had been sending full heat to the rear burner,but the problem ended up with the rear switch. The switches are interconnected and all are the same part number.Diagrams on partsselect were the key to a successful repair.To access the switch you need only to remove the fan cover, remove the 2 screws holding the switch assembly and move it foreward and then lift to reveal slide on connectors. Power to the unit is off at the main panel during the entire process. Read more...