Shindaiwa Chainsaw Parts

Stud-Guide Bar – Part Number: V225000031

Your Price

$4.99

Shindaiwa Chainsaw Stud-Guide Bar

PartSelect Number PS10053555

Manufacturer Part Number V225000031

Spark Plug Bpm-8Y – Part Number: 15901019830

Your Price

$3.99

Shindaiwa Chainsaw Spark Plug Bpm-8Y

★★★★★

1 Review

PartSelect Number PS9263506

Manufacturer Part Number 15901019830

This Spark Plug Bpm-8y is a silver and white OEM part. Made of steel and ceramic it is individually sold, and is an electrical part. It is installed with a spark plug socket and is rated as Easy to install. It is attached inside of the cylinder head, and is used to ignite the air fuel mixture inside the combustion chamber. You can clean the spark plug with a fine sandpaper of 180 or more, then spray it with carburator cleaner and wipe dry. However, even after regular maintenance, spark plugs need to be changed as part of good engine fine-tuning. Regap to manufacturer specifications. Refer to your owners manual or model number to ensure you are choosing the correct product. Note: If your engine has more than one cylinder and sounds like it has a miss, you can remove each spark plug wire one at a time to find the miss. If the engine drops in rpm when you remove the wire, then that cylinder is fine, if it does not drop then you have found your miss!

Your Price

$5.36

Shindaiwa Chainsaw Fuel Filter

★★★★★

2 Reviews

PartSelect Number PS11826311

Manufacturer Part Number A369000480

This OEM Fuel Filter is a silver and white, steel/felt, part measuring about 1.25 inches in length and 3/4 inch wide. It can be installed with pliers and is rated as Easy to install by customers. This part attaches inside the fuel tank to clean the fuel of debris, and should be replaced during regular maintenance, check your manual for recommended replacement time. If the filter is leaking or it has a blockage preventing fuel flow, then it should be replaced. If the engine sounds like it is not getting enough fuel, then remove the filter and check it for blockage.

Installation Instructions

Paul from SENECA, SC

Fuel line grommet rotted

This blower is quite old looked on YouTube. Removed grommet with needle nose pliers. Removed tank to install new parts. I had trouble getting return line off carb so planned to reuse it after grommet was in place. Thin was a mistake because the seated grommet compresses the holes. Took unnecessary time to get it through. With my trimmer with all lines in place. Hardest part was to get the grommet to seat even with silicone. Read more...

Your Price

$4.99

Shindaiwa Chainsaw Nut

PartSelect Number PS9236120

Manufacturer Part Number V265000200

This flanged hex nut is a genuine OEM steel fastener specifically designed for use in chainsaws and chop saws, serving the purpose of securing various components in these outdoor power equipment devices. It features a flange base that acts as a built-in washer for extra stability and security. The hex nut has a diameter of 6mm, and its threaded shaft has a pitch of 20, ensuring a secure and reliable connection. Over time, the bolt can be susceptible to corrosion, cracks, or worn threads, which may result in the loosening or detachment of the connected parts. Detectable signs of such issues include excessive noise, vibrations, and equipment instability. To address this, it is recommended to inspect all bolts within your equipment and replace any that are no longer functioning properly. To replace the bolt, simply use a wrench or socket to loosen and remove the old one, position the new bolt on the mounting surface, and securely tighten it until the flange is flush against the surface. Please note that each flanged hex nut is sold individually.

Your Price

$8.60

Shindaiwa Chainsaw Filter, Fuel

★★★★★

2 Reviews

PartSelect Number PS11826309

Manufacturer Part Number A369000460

The Fuel Filter is a white and silver, individually sold, steel part. It reuires pliers to install and its installation is rated as Easy. The part attaches inside of the fuel tank and is used to clean the fuel of debris. It should be changed regularly. Check your owners manual for the recommended replacement schedule for your engine. If the fuel is leaking or their is a blockage, you will know the part is broken and will likely need to be replaced. To check for small leaks, feel around for dampness and the smell of fuel.

Installation Instructions

Keith from NORWOOD, NJ

Replace clogged fuel filter.

Thru fuel cap, insert copper wire with hook formed on end. Fish around until you grab the fuel line. Pull the fuel line and filter thru the fuel fill neck.
Pull off old filter and replace with new. Push back into fuel tank & be done. Read more...

Your Price

$6.81

Shindaiwa Chainsaw Purge Bulb

★★★★★

2 Reviews

PartSelect Number PS8857246

Manufacturer Part Number 12318139130

This OEM replacement part is used to pump fuel from the tank to the carburetor in order to start the engine. It may also be referred to as a Primer Bulb. It is made of durable black plastic and is sold individually. This part will be found in various locations, depending on your model; refer to your owners manual to locate it on your machine, but is commonly found on the side of the air cleaner or carburetor. To complete this repair, you will need a screwdriver. The Purge Bulb needs to be replaced when it is cracked or damaged. It will become fatigued through regular use and may leak fuel when it is malfunctioning. Customers rated this repair as Easy.

Installation Instructions

Richard from SPRING HILL, FL

Bulb was worn out and broken open

The unit is a press fit. To remove the old one required breaking the plastic compression tabs that hold it in place. That was simple enough. Replacing requires lining up in the correct position to meet the inner hose. Then push it in. The compression tabs on the replacement click in and hold.in place. Read more...

Fuel Tank Vent – Part Number: A356000031

Your Price

$7.63

Shindaiwa Chainsaw Fuel Tank Vent

★★★★★

1 Review

PartSelect Number PS9183121

Manufacturer Part Number A356000031

This a a genuine OEM replacement check valve for your small engine. It is also known as a fuel tank vent. You may need to replace this part if you are noticing debris or dirty oil in the reservoir. Make sure the engine is cool before you begin this repair, and remove the wire and boot from the spark plug to prevent the engine from starting up.

Installation Instructions

Donald from ORANGE PARK, FL

fuel tank leaking around where lines went in tank

took all the old parts off and replaced them Read more...