First I removed the pan drawer. Then I removed the metal cover under the stove. Not sure if you have to remove that or not. I think I could have left that on. I then looked inside the oven and removed the two screws in the back to remove the lower cover. Ahh, the hot surface ignitor and flame grill exposed. I then turned on the oven again to make sure the hot surface ignitor was not glowing. I went back underneath, and disconnected the hot surface ignitor. I followed the wires from it to where it was connected. I then unscrewed the 2 screws that held the flame grill in place. Next, I went back in the oven and removed the flame grill with the hot surface ignitor still attached. I then unscrewed the hot surface ignitor and replace it with the new one. Key points: make sure you mark which wire had which connector, or only cut one at a time. Also, they do not come with new clips, so don't cut you wire too short. I then fed the wires and the base of the flame grill back down the slot, rescrewed the flame grill to the oven, attached the wires, and turned on the oven to make sure it worked. I finally replaced the lower plate inside the oven, the lower plate under the oven, put the drawer back in and I was done.

I had to pull the strorage drawer under the stove out to get at the electric connection for the ignitor. Then I removed the plate that coveres the burner and ignitor, and used a nut driver to remove the ignitor screws. I had to cut off the quick wire connectors from the old ignitor because the new one is just bare wires. FYI this is how the ignitor comes from every place I looked at, not just part select.com. After using the provided wire nuts to connect the new ignitor wires to the old ignitor wires that still had the quick connectors attached I screwed the ignitor back on. Put the covers on and done. It probably took about 30 minutes and saved me a bunch of money instead of having to call someone to repair something this easy.

Followed previous posts, just took out the metal pan (2) 1/4" head screws. Removed the ignitor bracket (2) 1/4" head screws. Disconnected the existing ceramic wirenuts. Removed the ignitor from the bracket......this was the hardest part as the self threading screw stripped out in the sheet metal. Took some time to remove that screw and re-tap the hole to #10-32. Once that was done used a #10-32 x 1/2" machine screw with lock washer. All went back together fine from there.

I put the grates in backwards and the wife had to turn them around after teasing me about it......maybe I should do more baking.......

I pulled out the bottom drawer, took out the interior bottom panel, and disconnected the ignitor. This repair is pretty straight forward. The only note I would make is that the ignitor did not have plugs on the end of the wires you have to splice the new ignitor in. If there are plugs available to purchase for your model, you may want to pick them up instead of splicing.

I followed the instructions I came across on this website (i.e., First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires). Removing the screws was difficult until I went to reinstall the igniter and relized you can pull the burner out all the way and quickly install the screws.

Your website help me troubleshoot the problem and locate the part. Part was delivered the next day. Following the instructions that others on your website had provided, the repair was quick and SUCCESSFUL.
Gas will not flow if the igniter is bad. Gas will only flow if the igniter heats up the internal bimetal strip which in turn, allows gas to flow through the safety valve
First, unplug the power sourse. For this repair it is not necessary to shut off the gas, but do so if it makes you more comfortable. Remove the oven door...it lifts right off. Next, remove the screws and lift out the bottom panel in the oven box. This will expose the igniter. Next, remove the lower drawer. Two 1/4-28 screws retain the igniter...remove these. With the drawer removed, go underneath and locate the 2 wires to the igniter. One has a green connector, and the other has a red connector. Disconnect these 2 wires and carefully remove the igniter and wires. Cut the wires from the igniter on the igniter end. You will need to reuse the plug end of each wire, so don't cut them too short. Splice these two wires to the new igniter with the wire splice caps provided. Feed the wires back down throught the opening at the back of the oven and carefully move the igniter into place. Install the two 1/4-28 retaining screws. Go back underneath the oven through the drawer opening and plug in the 2 wires. You should be good to go. Reassemble the oven and have mama bake a cake..

First remove the broiler drawer. I laid on my side and reached into the oven to do the work, I first removed the one screw holding the splash plate (in the rear) and lifted the plate out. Then, removed the two screws mounting the ignighter to the burner base. Cut the wires on the old ignighter about half way between the connectors on the safety valve and the ignighter. I used a utility knife to strip 3/8" of the insulation on the wires still connected to the valve. Then, mount the new ignighter. Route the ignighter wires behind the gas tube. Use the enclosed ceramic wire nuts to connect the new ignighter wires to the wires still attached to the valve. Push the wire nuts into the hole behind the valve. Reinstall the splash guard and broiler tray.

Unplug the electrical power first. Remove the drawer from the bottom of the stove. Then you can unplug the two wires that go to the ignitor. Inside the stove, remove the bottom cover plate by removing two screws at the back. You may need to loosen them with a flat screwdriver first. The ignitor has two screws that hold it to the long tubular part where the gas burns. There are two screws at the back which hold the tubular part (and one screw at the front). I removed the tubular part by removing these three screws. Then you can remove the ignitor, compare it to the new one to make sure it's the right part. Cut off the wires from the old part so you can use the same connectors. Splice these wires onto the new part, and insulate them with tape. Replace the ignitor onto the "tubular part" and attach it back into the oven. Plug the wires in, replace the bottom cover and drawer, plug the range back in and test it out. Mine worked great on the first try. The hard part is reaching to the back of the oven to remove (and re-install) the two screws that hold the "tubular part".

Before starting it's a good idea to disconnect the electricity and turn the gas valve off behind the stove.

Next, uncrew the two finger-screws at the back of the oven that hold the porcelain & steel drip plate in. It comes out if you push it towards the back of the oven and lift it out. This reveals the burner and the cylindrical igniter attached to the side of the burner. While I was there I unscrewed the one screw at the front end of the burner (nearest me).

After attempting the repair from inside the oven, I realized it was far easier to pull out the bottom drawer and work from under the oven instead. Using only one size mini-socket for all screws it was easy. I undid the two screws that hold the main burner to the back of the oven. This allowed me to pull the burner up inside the oven so I could access the screws that held the igniter to the side of the burner. A flashlight helps when working under the oven.

Under the oven again I then pulled the two wires off their respective connectors. Then inside the oven unscrewed the two screws holding the igniter to the burner. The old part came off very easily. However, the new part didn't have connectors attached, so I had to remember which wire went where and cut the old connectors off and splice them to the new. Be sure to leave yourself as much of the old wire as possible attached to the connector. Otherswise you might find the "new" wires too short to reach the connectors.

I reconnected the igniter to the main burner with the two screws. Then fed the burner and wires back into place. I then lightly screwed the single front screw on the burner (inside the oven) to help position the burner, then went underneath to install the other two screws.

Under the oven I made sure the wires fit onto their connectors then tightened the two screws to hold the burner to the back wall. Once the burner was properly in place I tightened the two screws and the single one inside the oven.

I then plugged the oven back in and turned on the gas flow. I turned the oven dial and watched the new igniter glow wonderfully.

Finally I replaced the porcelain floor cover inside the oven. These finger screws can be a bit tricky because they go into a threaded clip that might have moved while you worked. The whole task took less than 30 minutes - and I had never done this before.

First I disconnected power, then removed two screws from igniter & cliped two wires. Then installed new igniter & with the wire nuts supplied refastened to supply lines in oven.
PartSelect makes repairs quick & easy. It just takes a little smarts on your part.

The repair was fairly straight forward.

Step 1: Remove the storage drawer from below the oven and disconnect A/C power.
Step 2: Using nutdriver, remove the 2 machine screws in the front and 2 on the sides that hold the silver cover plate under the oven.
Step 3: Disconnect the 2 wires going to the igniter and remove the 2 bolts holding the igniter to the burner assembly.
Step 4: After removing the defective igniter, cut the connectors off the old igniter.
Step 5: Strip the wire on the connectors back the appropriate length and connect them to the new igniter with the supplied ceramic wire nuts.
Step 6: Reinstall new igniter into the buner assembly and reconnect wires.
Step 7: Before reinstalling the cover plate, plug A/C power back in and test that the igniter glows orange and the main gas valve opens.
Step 8: Assuming your test light worked, reinstall cover plate using 4 screws and put the storage drawer back in place.

I pulled the range out from the wall so that I could unplug the power card. (I eventually discovered that I didn't need to pull it out from the wall--there is a separate plug under the stove, behind the bottom drawer, that I could have simply unplugged instead.)

I removed the bottom drawer of the range then removed the racks and bottom tray from the oven. I then removed the baffle above the oven burner by removing two screws. At this point I could see the igniter. I removed the two screws that attach the igniter mounting bracket to the back of the oven. I removed one screw that attaches the igniter to the mounting bracket. At this point I pulled the igniter out several inches and cut the wires where they were attached with ceramic wire nuts.

I stripped about 1/2 inch insulation from the wires coming through the back of the oven and used the new ceramic wire nuts to attach the new igniter. I then reversed the above steps to complete the repair. I had read someone else's repair report and took their advice to lift out the burner pipe to get more working room during disassembly and reassembly.

The unnecessary steps that I took were: (1) Pulling the stove from the wall. (I could have unplugged it from another plug at the bottom of the stove.) (2) I took the cover off the electronics box-- two screws--underneath the stove because I thought I needed to get access to the wires, but that was not necessary.

The parts list claims that the oven igniter is very fragile. I disassembled the old one (and I mean I really took it apart!) and I found that it was quite rugged mechanically. The failure appeared to have been an internal connection from the wires to the heating element. I don't think it is very fragile to handle.

Unplugged the oven. First i removed the 2 screws from the pan at the bottom of the oven and took the pan out. Next i took out the drawer underneath and took the screws out of the pans below to get to the ignitor. Unscrewed the ignitor and cut the wires below it to splice the new ignitor on. Spliced the two sets of wires and put the ceramic wire nuts on. Replaced the top and bottom pans and put the drawer back. plugged the oven back in and started the oven right up. Pretty easy.

removed the gas burner which allowed easy access to undo the old igniter.
opened the wire hatch in the back of the oven cavity, and also took off the cover (two screws) on the back panel to allow access to the igniter connector.
I cut the wires to the old igniter, leaving lots of wire, stripped the wire, and then hooked up the new igniter using the supplied ceramic / hi-temp twist on connectors.
then just closed up everything in reverse.
helps to take off oven door, and you need access to the back side of the oven.

Removed bottom of oven Removed bottom drawer. Removed two screws holding burner, disconnected both wires.Removed two screws holding igniter,installed new igniter reversing procedure.

Could not get at the screws holding the igniter to the buner, without removing the burner.