993287-1-S-Whirlpool-8577274           -Internal-Bias Thermistor
993287-1-S-Whirlpool-8577274           -Internal-Bias Thermistor 993287-2-S-Whirlpool-8577274           -Internal-Bias Thermistor

Internal-Bias Thermistor

PartSelect Number PS993287

Part may differ in appearance, but functions the same as original part. This part controls the temperature of the inside of the dryer drum and prevents the dryer from overheating.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • No heat or not enough heat.
  • Shuts off too soon on auto dry.
  • Will not start.
  • Temperature too hot.
  • Takes too long to dry.
  • Compare At

    $27.28
  • You Save

    $4.55
  • Your Price

    $22.73
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.5 / 5.0, 11 reviews What's this?
1-11 of 11
 

122 of 140 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:More than 2 hours

ToolsNutdriver, Socket set

CustomerSteven from East Norriton PA

Dryer overheated, blew out thermal fuse

I started to repair this and got busy and ended up calling a repair service -- that was the first time. They repaired it for over $200 and said the cause was bad venting. I fixed the vent before using the fixed dryer but it blew again. So I ordered these parts and replaced them myself for a lot of savings. However, the dryer still overheated. Through lots of testing I found the root cause the repairman missed: The heating element had gotten so hot that the assembly holding it warped, hitting the element and shorting it. So a new element is on order. I still needed the parts I ordered here but the overall repair ended up more complicated and expensive. I was disappointed a paid repair person left without further diagnosis. If he had unplugged the vent and checked the heat on the exhaust vent (as I ended up doing) it would have been obvious more than a new thermal fuse/thermistor was necessary. Instead I wasted over $200 on his visit. So my advice is if you're at all handy, repair this yourself. The dryer has a service manual inside the front toe board that walks you through most diagnostics and tests. However, it took a little more than that for me to discover the heating element problem. This was a very dangerous situation that could have easily led to a fire, yet not found by a trained technician!

Help other customers find the most helpful instructions.

Were these instructions helpful?

13 of 16 people found this instruction helpful

Parts Used

  • Internal-Bias Thermistor

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers, Socket set

CustomerJim from Tucson AZ

Unit would shut down in the middle of cycle and flash e1 trouble code

Had to remove the back of unit to access the area of subject part by removeing 12 to 14 screws also the gas line had to be removed. Two screws held the part in place. Unit now runs normal.Saved alot on repair costs!!!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

10 of 12 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers, Wrench set

Customerprem from brandon FL

Dryer dial when set and turn on it turn off in about 2 minute.

dryer remove bottom panel and r&r thermistor very easy to do. your self diagnose help I could not have done it

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 7 people found this instruction helpful

Parts Used

  • Internal-Bias Thermistor

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver

CustomerDixon from Santa Fe NM

Dryer turns off after 1-2 minutes

I tried to follow directions followed by others on this site after diagnosing the problem via suggestions provided by users. I have a Whirlpool Duet dryer from 2002. We've had problems since moving about 3 years ago. I removed the front panel (lower) by unscrewing the two bottom screws (1/4" sheet metal screws). Then I took out the lint screen and the metal tube/contraption immediately beneath to get access to the area where thermistor is located. See the drawing/chart to help you locate this. It's really easier than it seems. Make sure you have the chart/drawing for your model - it makes difference! The thermistor came out pretty easily with a nutdriver that has a swivel offset shaft. Ask your hardware store tool dept. about that one. Put everything back in reverse order of course and test either with/without the front panel re-attached. In my case it fixed at least part of the problem. I was able to get clothes almost dry with most settings but I have yet to install the moisture sensor to see if that helps in addition to the internal-bias thermistor. I am the kind of person that does one thing at a time so at least I now know the thermistor was bad. Good luck and hang in there with your own repair. It's a lot cheaper even if it takes you longer to do than a pro.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

  • Internal-Bias Thermistor

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerJoyce from Holbrook NY

When using the dryer the cycle would stop and display e1 as the reason

Unscrewed the bottom panelof the dryer and located the thermistor through the schematic for my machine. Removed the old one and put the new one in the same way. No more E1 problems and all cycles now complete themselves.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 7 people found this instruction helpful

Parts Used

  • Internal-Bias Thermistor

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Socket set

CustomerDwayne from Bainbridge PA

Dryer would shut off mid way through cycle and give an e1 error code

After turning off the power to the dryer I removed two screws to the bottom front panel and droped it out of the way. I remved three screws hloding the lint screen in place just for better axcess to the element. I then removed the two wires attached to the element and then the two screws holding the element in place. I put everything back together in reverse. I also took the time to clean any dust and lint out.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 9 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerEugene from Columbus NJ

Switch broke and would not light the refrig compart

The repair descripition was accurate. The difficult part was getting the old switch out. It has a release clip that is hard to reach. It took several tries and a bit of force to get the old part to release from the cabinet.

In stalling the new part was easer that the instructions explaned. There was no need to split the original plug. I unplugged the old switch, plugged in the new and snapped it into place. 30 seconds after I started the reinstall it was in the cabinet and working

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 10 people found this instruction helpful

Parts Used

  • Internal-Bias Thermistor

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Socket set

CustomerBrad from Wausau WI

Gas dryer shut off mid cycle in timed cycle mode

Removed the lower front cover of the dryer. Removed the lint filter and removed the cover from the air duct by removing two 1/4" bolts. Removed the two 1/4" bolts retaining the thermistor. Installed the new thermistor and covers.

Help other customers find the most helpful instructions.

Were these instructions helpful?

25 of 155 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsSocket set

CustomerRonald from Louisville KY

Dryer shuts off on any cycle except "air only"

I read in the forums that thermistor replacement fixed this issue 56% of the time. I replaced the thermistor and then ran three loads of clothes through a one-hour dring cycle at the highest temperature and the dryer did not shut off.

Help other customers find the most helpful instructions.

Were these instructions helpful?

38 of 633 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerApril from Verona WI

Power would come on, but dryer would not start

Put both parts in and it started (not sure if we needed both, but my husband put both in)

Help other customers find the most helpful instructions.

Were these instructions helpful?

75 of 1895 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers, Socket set, Wrench set

CustomerHenri from Las Vegas NV

My dryer would shut off and would not dry the clothes

I replaced the thermistor and the thermostat and it fixed the problem. The recommended parts worked just as advertised. This website is great!!!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-11 of 11