992506-1-S-Whirlpool-2315562           -Thermostat
992506-1-S-Whirlpool-2315562           -Thermostat 992506-2-S-Whirlpool-2315562           -Thermostat 992506-3-S-Whirlpool-2315562           -Thermostat

Thermostat

PartSelect Number PS992506

Helps to maintain the proper temperature in the freezer and fresh food compartments.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Fridge too warm.
  • Fridge too cold.
  • Will Not Start.
  • Compare At

    $71.45
  • You Save

    $11.91
  • Your Price

    $59.54
In Stock
Order within the next 12 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.5 / 5.0, 2 reviews What's this?
1-2 of 2
 

33 of 41 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Screw drivers

CustomerRichard from owasso OK

Freezer freezes but refridge is warm

refridge never cooled good,replaced termostat and circuit board, works great probably over kill but better than waiting on parts. Very easy job, drop over head control panel , remove thermo very carefully after unhooking linkage to freezer vent to fridge, be carefull not to bend linkage, you will also have to remove 2 covers that shield thermo conduit for thermo that go to back of fridge. Board is very easily replaced when sitting on table but 1 plug gave me problems trying to release the plug, {hint} move side to side instead of moving up and down . The themo stat sencing tube install is kind of trickie too , just straighten the tube totally before trying to remove or reinstall the new sencing tube, you can form it during restlall in the fridge . It was good to see that fridge cooling back down to 34 degrees on less than mid setting. YAHOOOOOO

Help other customers find the most helpful instructions.

Were these instructions helpful?

25 of 30 people found this instruction helpful

Parts Used

  • Thermostat

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerGarry from Ochelata OK

Food freezing in the refrigerator

Remove the front panel strip where the temperature adjustment lights show, use a thin screw driver to pot the strip out along the top. Use a nut driver to remove the control panel which contains the light, two bolts on the under side, two bolts on the front after the panel strip was removed. The control panel will hang down enough with the wires attached to allow access to the thermostat. Use a Phillips screw driver to remove the side cover where the temperature probe runs along the left hand side to the unit, one screw. You will find the temperature probe inside plastic tubing running to the back of the unit where it is wrapped around a Styrofoam holder with three plastic retainer clips on the top and bottom. Unplug the thermostat from its electrical connection. You may want to unplug the unit’s wall plus as this is 110 volt connection. Remove the two screws holding the thermostat to the plastic control panel; remove the fiber optic connection to the light strip that runs across the top of the thermostat. Remove the temperature probe from the 6 clips and pull the entire unit out. Remove the plastic tube from the old temperature probe and slide it over the probe from the new thermostat. The probe is approximately 26 inches long and you must take care not to crimp it as you slide it in the plastic tubing(warm the plastic tube with a hair dryer to reduce stiffness at the bend). Plug the wires into the new thermostat and reassemble.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-2 of 2