Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS9861764
May differ in appearance but functions same as original.
This part works with the following brands: GE, Hotpoint & Kenmore.
This part fixes the following symptoms:
Took front of dryer pantel off and replaced parts ordered.dryer sounds very quiet like new dryer.
Help other customers find the most helpful instructions.
Were these instructions helpful?
I read over other people's repair stories and it seemed like something I could do myself, so I gave it a shot.First I unplugged the dryer and wrestled it onto my back porch, because I don't have room to work in my laundry room.1. I removed the door by unscrewing the 4 hinge screws.2. I removed the 2 screws at the top of the recess the door fits into.3. I removed the top of the dryer.4. There were 2 inner screws holding the front in place (which is why the top had to come off, because there is no other way to get at those screws...and they are near the top of the dryer at each front corner)...I removed these to take the front off. I had to use a flat-tip screwdriver to pry it out at the bottom, but it wasn't very hard to do. I also disconnected the wires, which was easy, but just be sure to note how they hook together so that you get them hooked back together correctly.5. I removed the old felt, noting how it was positioned so I could install the new felt correctly.6. I removed the old drum bearing. It was cracking on the top of it, and all 4 slides were totally gone, so I'm glad I ordered all 4 of them!7. I cleaned everything up and found .37 cents in change!8. I installed the new drum bearing...it just clips into place.9. I installed the 4 slides. I had watched a video here on how to do that, and it really is super-easy. There was just a bit of one green/gray slide left, so that told me which went where.10. I installed the new felt.11. I reconnected the wires and put the front on.12. I put the top on.13. I put the door back on.14. I wrestled the dryer back inside and plugged it in.15. I turned it on to test it...it worked, and NO MORE SQUEAK!!My dryer has been working great ever since. I would like to note that I bought this dryer used, so I really am not sure of how old it is...so I guessed. It seemed to be in good condition, and the person I bought it from plugged it in and let me see that it worked...and it didn't squeak then. It started squeaking about halfway through the first load of clothes I did. Still, I got it at a good price and luckily it didn't cost too awful much to get the parts needed to silence that squeak.I am really thankful that there is a site like this to help people who might not be able to afford a repair other than to do it themselves. I know some just don't like to pay the high cost of repair, but some (like me) simply don't have the money for that. So thank you VERY MUCH for all of your help...it is greatly appreciated!!
The top and front of the dryer had to come off, and taking off the top (and later putting it back on) was the hardest part. The old seal was stretched approximately two feet longer than the replacement part, and its thinness caused the drum to squeak as it scraped by the door panel. We simply pressed the new seal into place after pulling out the old one. Piece of cake. Putting the front of the dryer back on was simple as well. Fitting the top back into its slots properly was the biggest pain of the whole ordeal. The part came in about 2 days. Thanks!
1. Remove Door 2. Remove two screws holding top of dryer on then slide top out. 3. Remove two screws holding front of dryer on. They're towards the top on the inside Then remove front. 4. Drum bearing just snaps out, so just pull or pry it out. And install new one. Just snaps in. 5. Install Drum slides. Make sure you order all four !! . 6. since you have it all apart you should vaccuum any excess debris (lint) out. 7. Put it back together. The top slides in and down , mine needed a "little persuading" back in. Make sure the gasket around the lint tube is still there or lined up properly (mine fell off) . I changed the felt strip also, if you do it make sure you pay attention to how it came off !! You have to stretch it a little.
Removed Two Screws securing top of dryer to front of dryer. Removed 4 screws securing button panel to back of dryer. Removed top and set it to the side.removed 2 screws securing front to sides and removed front of dryer, leaving electrical connectors connected. Removed old felt from lower drum support and removed old worn out upper drum bearing(only one slide was left). Snapped new drum bearing into front, installed new slides on drum bearing and new felt. Reinstalled all components in reverse of dismantle and fired her up. Works like a charm. My children hated the electrical dryer I was using in interim.
4 screws, that was itopen the dryer door, locate the 2 screws that hold the top in place, unscrew themthen locate the 2 screws (located near the top of the dryer (facing toward you) and unscrew themallow the front of the dryer to tilit out towards you, replace the felt, slide the drum back into place into the front of the dryer, resecure the 2 screws (removed last)lower top of dryer back in place, being careful to make sure the top clips back in correctly.re-install the 2 screws that secure the dryer top to the front.boom, you are done....Amazingly easy work...
First with a screwdriver,I removed the two screws and lifting the top and the front panel of the dyer off. The worn parts were easily removed and the new parts just snapped into place. I then just put the front and top panels back on and the whole job took less than 20 minutes to complete. The next day I received a letter from GE that the warranty would expire and would I like to buy an extention. Thanks to PartsSelect I saved a lot doing it myself.
The dryer made a loud squeal and I shut it off immediately. 1 - Unplug the dryer2 - Took the top off and the front off the dryer3 - Removed the 4 Front Dryer Drum Slides that were worn all the way through4 - Pulled the bunched up Felt 5 - Vacuumed out the inside of the dryer -Very Important6 - Put the drum slides in and felt piece7 - Put the front on top back on 8 - Worked great
Took top and front panel off. Pulled top bearing shroud off, replaced and installed the slides on new top bearing. Installed felt gasket on the bottom piece of lower shroud. Installed new lamp and put back together to check out. Dryer working great now. Should have changed the belt but it is not squelling so it is fine.
Opening the dryer door and removed the two screws located at the top of the opening. Pop off top lid of dryer by lifting up on front, and slide forward. I needed to break it loose by prying it up with a screw driver (use light pressure, be careful not to bend/scrape top), as it was first time every being removed. Remove two screws at top of front panel, hold up drum, and pull front panel forward. Unplug electrical cable to door, and removed front panel. Removed and replaced all four slides (2 Green slides & 2 Clear slides). Removed felt drum seal and replaced by lightly pushing in slots (couple of very light pushes using a screw driver was also needed). Placed front panel back on slots at bottom of dryer (REMEBER TO PLUG IN DOOR SWITCH), lifting (lightly) up on drum, and push in place, replaced all parts in reverse order. Top was a little tricky getting back on, but with a little push it snapped in place. Plugged in dryer performed test run everything worked perfect. Thanks to PartsSelect for their quick response to my order, you are definitely on my favorites listing for any future repairs and/or help.
UNPLUG DRYER FIRST.Open dryer door find 2 screws at top of dryer door opening ( pointing upward). Remove screws and pop top panel of dryer up and remove it. Remove 2 screws near top of front panel (on the inside facing toward you). Careful not to drop them down into dryer interior. Pop front panel with door attached forward by tilting toward you. then lift off bottom tabs and turn panel / door assembly to the side. Careful not to pull wires at bottom loose. Carefully pop "Drum Bearing" off. This is the half moon shaped part that the "Drum Slides" (2) clear and(2) "green" pop on to. Replace drum bearing. Put new slides (4) on drum bearing. Replace felt seal. Place front panel back on dryer by carefully lifing dryer drum up while pushing front panel onto dryer. This allows the drum to "sit" on the felt seal. Put screws back onto top of front panel. Replace top panel , which can be tricky, by aligning tabs near contol panel with slots on top panel then lowering front of top panel into place. Then put screws back near top of door opening to secure top panel. Test dryer by turning off the heat on the heat setting knob and allow dryer to run for a time. Then try it with some clothes and heat. If it is still making noise then check rear bearing/bushing. Mine was fine and this repair fixed the issue. By the way, all but one of my 4 slides were worn to nothing and the drum had been "eating" into the "drum bearing making it paper thin in several areas. The felt was worn out also. This allowed the drum to settle down and gap at top which allowed clothes and dryer sheets to get caught between drum and dryer cabinet.
Took the front of the dryer off to expose drum area and replaced parts needed and reinstalled cover one of the easiest repairs i have ever done.
first ,removed two screws from inner door lining.removed top by lifting front up and off.removed two screws holding front panel onto side panels.lift and pull up front panel away from main body of dryer.turned it around watching not to damage wires. remove old felt and install new felt.put everything back together in reverse.dryer works great.
Replacing the dryer drum slide took the most time. Opened the dryer door and removed two upper screws that held the frong section of the dryer. Lifete dthe barrel and remove dthe front cover. replaced the drum slides no probelm. Found other components faulty, placed order
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.