| |
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerJustin M from Cypress TX
Ice door gasket warped would not seal
Pop off the control board for the ice selector/water. Remove power / signal connections. remove four phillips screws, Remove plastic hopper. Pop off Ice door gasket, pop in new one and put back together. If you fridge was sounding like it was speeding up and slowing down, this will correct this problem as well.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerRene from Lancaster CA
Water flow from in-door dispenser was a trickle
We didn't think the dispenser problem was related to the filter - we were wrong! It took less than two minutes, including opening the box and unwrapping the filter. I'll definitely be changing my filter more often - and buying it through PartSelect. Your ordering was so easy and delivery was unbelievably fast!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsNutdriver, Pliers
CustomerBrent from Williamsburg VA
Freezer would not auto defrost; needed new filter
Unplug Fridge unscrew rear compartment where main board was located, unfastened old board.
Unplug one wire harness from the old board and fit on the new board, repeat until the new board was wired, secured new main board to fridge.
****Manually defrost freezer before restarting. ****
WAY LESS THAN THE PRICE OF A REPAIR VISIT.
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsPliers, Screw drivers
CustomerLeonard from Hawthorne CA
Replace dispencer blade
Removed the exterior 4 screws and 1 holding the metal rod underneath. Sepearated the plastic parts pulled out the dispensing mechanisim. Removed the lock washer, then removed the spacers and blades. Put the new blades in with the spacers and reversed the other steps and done.
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:1- 2 hours
ToolsScrew drivers, Socket set, Wrench(Adjustable)
CustomerJ Michael from Rockville MD
Ge refrigerator water dispenser didn't work
I am very handy and figured it out by myself. I installed the water valve - bracket assembly and control board within an hour and the dispenser works fine. I recommend that you all make installation links on line more user friendly. Thanks.
J M Joly, MD
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
Tools
Customersusan from hartford WI
Bad tasting ice cubes
Took the old filter out and put the new one in.
Easy Breezy!!
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
Customerrichard from asheboro NC
Needed to replace the filter
replaced the filter with the new one i purchased
|
0 of 3 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerMary from Elk Grove CA
|
0 of 3 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerJAMES from MORENO VALLEY CA
Water dispensed at a trickle
I only had to remove the old filter and install the new one - all by hand. I then ran about 1 to 1and1/2 gallons of water through the filter to clear it.
A WORD OF CAUTION - HOLD YOUR GLASS CLOSE TO THE WATER DISPENSER FOR THE INITIAL FILLING - IT WILL SPIT UNTIL THE AIR IS PURGED FROM THE SYSTEM!!!
An extremely easy repair.
|
1 of 7 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerGerald from Lincolnwood IL
Ice dispenser was always crushing ice, and slow water dispensing
Replacing the water filter with the new style water filter was no problem...twist to the left, drop the old filter, line up arrows on housing and new filter, twist to the right and done.
Ice maker was always crusing ice. There is a spring deflector wound around the actuating rod towards the back of the ice dispenser. Pulled the ice dispenser out, slid the damaged spring off, and slid the new spring deflector on making sure to engage the actuator rod to restore it's action. Easy fix.
|