| |
1 of 4 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:15 - 30 mins
ToolsPliers, Screw drivers
CustomerJack B from Walnut Creek CA
Red spring broke - refrig sect. Door closure
I found that I did not have the strength to stretch the new spring enough to install it initially. Using a 1/8 or 5/32 inch allen wrench I removed the pivot for the arm that the spring applies tension to. This allowed the spring to be easily attached to the hole in the arm and to the post in the bottom of the refridgerator. I then used a small pliers to grab the arm in front of its pivot hole and pull it against the spring into position to replace the pivot. Replacing the filter was surprisingly easy. I turned the water supply valve off under the sink and easily unscrewed the old filter (about a quarter turn). I filled the new filter with water and srewed in in. No wrenches required. I turned the water back on under the sink and everything works great!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerRobert from Jupiter FL
Water spilling out of back of refrig.
PartSelect ROCKS! Couldn't have been easier to do the repairs. Parts arrived in 2 days, everything I ordered was in the box. Minutes later my refrigerator was fixed!!!Thanks PartSelect, looks like I don't need the yellowpages anymore! P.S. I ordered a part I didn't need, called customer service and the return process couldn't be simpler. I will happily use you again and highly recommend you to my family and friends.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers, Screw drivers
Customerrafael from Pompano Beach FL
Water wouldn't come out and wouldn't work
After receiving the parts from you guys, by the way, supper fast shipping, next day, installing them took no more than 10 minutes, put the cover plug it in, and fresh nice water coming out. Next day, the ice tray was full of beautiful ice cubes.
So supper happy that I didn't have to buy a new refrigerator and I was able to fix it for under $300. I hope it can last now at least another 10 years.
Thanks
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsNutdriver, Screw drivers
Customeredward from orlando FL
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerKELLY from ARLINGTON VA
Broken microwave handle
Unscew top screw, remove seal from inside door, remove bottom handle screw, replace w/ new handle, replace seal.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerRobert from Myrtle Beach SC
Yearly replacement of filter
Moved stuff out of my way on the top shelf, reached in and turned old filter to remove. Filled new filter with water, lined up and turned to lock in place. Whew, never thought I would get that job done. :-)
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerMarilyn from Green Valley AZ
Needed new water and ice filter
simply read the instructions
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerBeverly from Jacksonville FL
Bad tsting ice cubes/ water
it was easy. Open the fridge,untwist the old filter. Open the new filter, fill with tap water and twist in place. Run water through it for a few minutes to insure it is working and filters the water.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsNutdriver, Screw drivers
CustomerDarl from Bedias TX
Ice formed on freezer coils blocking cold air flow to fresh foods section
I removed sheet metal covering coils, held in place with 4 screws. I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Replaced bad heater element with new one in reverse order.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerRichard from Kingsport TN
Scheduled replacement
Turned the old filter loose, removed the adapter from it, put the adapter on the new filter and turned the new filter back into place.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerCharles from Enterprise AL
Water tasted funny
Simply twisted off the old water filter, unwrapped the new one and twisted it on.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsNutdriver
CustomerArthur from Ware Shoals SC
No water to water despenser
replaced the water valve,valve does work but still no water to dispenser problem inside door
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerPorfirio from Hainesville IL
Fridge was warm, built up of ice in freezer
I had a buddy come over that is a bit more mechanically inclined than myself come over to install it. To remove the old part and install the new one was not difficult to do. I could have done it.
I would also suggest to check the Defrost Heater in the Freezer. We replaced both to be sure. So far Fridge working AOK, saved $$$ doing it ourselves.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerMaurice from Palm Beach Gardens FL
The lid of the top load washer would not stay open, it flips down.
Insert a screw driver, in the space between the cabinet and the top to release the two latches, then swing the top open to expose the screws holding the lid hinge. Remove the screw of each hinge, and replace the two hinges.
|
2 of 7 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerKenn from Shasta Lake CA
Ice in the door would no longer eject ice; stuck
Problem: The hardened ice crushing blades had worn the shaft causing them to "lay over" and get stuck.
Remove the ice maker drawer. On the bottom remove two phillips screws to take off the front cover.
The interior white insert in the front has two tabs that hold it in place. Releasing this is the hardest part. I used a small straight screwdriver to CAREFULLY pry the sides away from the tabs so that it could be lifted out. This removes the whole ice ejector and auger shaft.
Lift out the shaft, leaving the crusher blades in order.
Slide the new auger shaft into the crusher blades, pop in the back part and reassemble!
|