| |
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerShela from Greenbrier AR
The door latch broke & dishwasher wouldn't start.
First I removed the 9 screws holding the front panel of dishwasher on. I then removed the 2 screws holding the latch on and unplugged the 4 wires that was connected to the latch. Then I plugged the 4 wires into the new latch screwed the new latch in place with the 2 screwsI had removed. Put the front panel back in place and screwed it down with the 9 screws I had removed. And the dishwasher is working like it should now. It took me about 10 min, to do the job.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsScrew drivers
Customerdana from sunderland MA
Handle was broken
1. turn off power
2. put an old blanket on the floor under the opened door.
3. unscrew six phillips screws (it's not necessary to unscrew all the screws, only the ones at the top)
4. remove two torque screws securing handle
5. remove handle
6. unplug four leads one at a time transferring leads to new handle in the same location
7. replace two torque screws
8. replace six phillips screws
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerMichael A. from Lodi CA
Broken latch release button
removed the screws that hold the upper portion of the door. removed two torx screws that held old latch. attached new latch, then swapped out wires from old latch to new one.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerCody from Washington UT
Broken latch
I simply removed the screws to the door of the dishwasher and removed the panel. Then I unscrewed the old broken latch by pulling the wires and removing two more screws. Put on the new latch and door and it was done. about 10 min. was all it took and I saved about $100 by not calling a repairman. The parts even came with easy directions. Thanks!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:30 - 60 mins
ToolsNutdriver, Pliers, Screw drivers
CustomerAlex from Conyers GA
The latch broke-door would not stay closed
i removed the front of dishwasher and replaced latch anfd gasket around the door
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerCraig from North Brunswick NJ
Dishwasher would not start and door did not close properly
Removed the screws that held the control panel to the door, gently removed the control panel, loosened the two screws the held the latch mechanism to the door, unplugged the electrical connections to the switch, then reversed the process using the new part.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerLiz from Rolling Hills Estates CA
Handle broken
Everything was super easy except getting the door panel back on. I later read I may not have had to remove the panel to replace the handle but I did. The panel was difficult to hold in place as the screws are replaced and took two people.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerBrian from Berwick ME
Door latch broke
Shut off Circuit Breaker
Removed screws from Door
Removed front Panel on Door
Removed old Door Latch
Installed new Door Latch
Replaced front Panel
Reinstalled screws
Turned on Circuit Breaker
Closed door and Ran Dishwasher
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerDonald from Snellville GA
Handle broke during use.
First I removed the cover plate over the front of the dish washer. I then removed the old handle and disconnected the 4 wires one at a time, hooking them to the new handle one at at time, in the correct pattern. Positioned the new handle and screwed in the 2 screws needed to secure the handle back in place. A very simple replacement.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerCory from Oak Park IL
Plastic latch was broken
Removed the screws holding the cover plate, the two screws holding the latch, and switched it the wires from the old latch to the new. Replaced all screws, now it works like new.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
Customerthomas from houston TX
Broken latch
Removed 6 screws to remove housing.
Removed 2 screws to remove old latch disconnected 4 female plug connectors.
Reconnect the 4 plugs to the new switch & re-mounted it with the 2 screws. Slight misalignment (which may have been present before the repair) was corrected by bumping the metal latch receiver withe the handle of the screw driver just a bit. Works perfectly.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerDoug from Fremont CA
Door latch broke, couldn't close the dishwasher door
Ordered the part, unscrewed 6 screws. Took out the old part put in the new part. Took less than 10 minutes and we were washing dishes again.
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerJarold from Palm Harbour FL
Latch quit functioning
New latch comes with new gasket. The instructions are simple enough for the installation, but the new gasket needed some compressing before the latch would stay in the "closed" position without popping back open (due to the thickness of the new gasket in the lower area). I tried reinstalling the gasket a couple of times, nothing helped. It just took some time to compress. Also, the new latch varies slightly from the original, but still works perfectly.
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerEldon from Black Mountain NC
Latch was not working
Wow. I am now an appliance repair man. I fixed the dishwasher which was somewhat easy and all works well. Just a few days after the dishwasher was done the clothes dryer shut down. Since I am an now an appliance repair man I decided to tackle the dryer. I got out my meter and checked the parts and found that all I needed was a thermostat so I ordered it from parts select. My wife is so impressed, I saved a bundle and the service from parts select is great!
|
0 of 3 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerMonica from Houston TX
Dry knob and dishwasher handle broken
The Dry Knob was a no brainer, I just replaced the existing knob.
The Dishwasher handle was fairly easy. I had to removed the dishwasher door and remove the broken handle. Removing the handle was a bit difficult, but once it was removed everything else went very quickly.
|