| |
29 of 32 people found this instruction helpful
Parts Used
-
- Thermal Overload Safety Thermostat
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsNutdriver, Pliers
CustomerFrederick from St. Louis MO
No heat after cleaning oven
This built-in oven was slid out of it's space and set on a box. I removed the back cover with nut driver and located the safety overload device. removed nuts and used pliers to remove wires and replace them. The power must be off to do this repair.Replaced the cover and slid back into place. This could be a lot more difficult if your power cord or gas line is not long enough to make it out of your wall space. Or of your oven is attached well to the frame.
|
6 of 6 people found this instruction helpful
Parts Used
-
- Thermal Overload Safety Thermostat
Level of DifficultyReally easy
Time to do repair:1- 2 hours
ToolsPliers, Screw drivers
CustomerElvin from Richmond VA
Oven would not heat
This is a drop in range so I had to remove the range and set on a dolly. Turn the dolly around and acess the THRMST-FIX that needed replaceing, it was open. put the range back in its place and could still use the rest of stove until I received the parts 2 days later .
Pulled the range out put the new THRMST-FIX in put the range back together and put the range back in place and it has worked ever since.
GOOD JOB
|
6 of 7 people found this instruction helpful
Parts Used
-
- Thermal Overload Safety Thermostat
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsNutdriver, Screw drivers
CustomerDevin from Platte City MO
Oven wouldn't heat after cleaning cycle
Turned power to oven off. Removed trim screws and trim. Removed screws that anchored oven in cabinet. Removed oven from cabinet. Removed back panel, tested thermal fuse. Determined it was defective, ordered new part and reversed procedures above to reinstall.
|
4 of 6 people found this instruction helpful
Parts Used
-
- Thermal Overload Safety Thermostat
Level of DifficultyEasy
Time to do repair:Less than 15 mins
Tools
Customerkaren from bismarck ND
Quit heating
I have a rental and the tenant called. She said that she had a repair man out to fix the oven but he couldn't~that it needed to be replaced as he could not get parts.I contacted your company via phone and the person was so helpful~he asked the problem, looked up the model and advised me on this!It works like a brand new oven!Thanks you
|
3 of 4 people found this instruction helpful
Parts Used
-
- Thermal Overload Safety Thermostat
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerKenneth V. from Kent WA
Upper oven bake and broil elements fail to heat when keypad entries made and indicating correctly
Replacement of the thermal overload safety thermostat very straight forward after sliding unit out, killing power and removing two covers. Tested both old and new and both show continuity (= good). Installed new, restored power and tested for proper operation. Didn't happen. Replaced original and now have new as spare. Now suspect the double line break relay on electronic control board is failed and source of problem. It is common to both elements and immediate before the suspected thermostat in circuit.
|
4 of 8 people found this instruction helpful
Parts Used
-
- Thermal Overload Safety Thermostat
Level of DifficultyA Bit Difficult
Time to do repair:30 - 60 mins
ToolsScrew drivers
CustomerRobert from Willow Park TX
Oven wouldn't heat after a cleaning cycle
Recieved the part promptly. From looking at the diagrams, we knew the overload thermostat was located on the back of the oven. We removed the screws, brackets, etc, slid the oven out, which for us was fairly easy as it's an under counter oven. Located the thermostat, removed it, replaced the new one, connected two clip wires, replaced the oven, turned the power back on and it works like a champ. Total cost was under 50 bucks.
|
2 of 3 people found this instruction helpful
Parts Used
-
- Thermal Overload Safety Thermostat
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
Customerjoyce from thomasville NC
Every time I would try to do the self clean mode on my drop in range the thermostat blows. Last time it was still under warranty. I took the part number from the repair man's invoice to order the new part.
My husband took the back off and replaced it. The repairman suggested pulling the range out into the floor to run the self clean mode. I have owned several such ranges and have never had to do that and won't now. Easy Clean Oven Cleaner will be the next thing I use.
|
1 of 2 people found this instruction helpful
Parts Used
-
- Thermal Overload Safety Thermostat
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerRod from Dripping Springs TX
Neither bake nor broil elements came on
Removed four trim pieces; removed four wood screws holding oven in cabinet housing; slid oven out (weighs about 150 lbs and takes two people and a bench to rest oven on. Oven will pull all the way out but not much further because of the electric cord.); Removed back sheet metal cover (bunch of small metal screws); removed wires from bad unit, unscrewed the bad unit and screwed in the replacement unit.
|
2 of 9 people found this instruction helpful
Parts Used
-
- Thermal Overload Safety Thermostat
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerJoi from Higginsville MO
Oven wouldn't heat after self-cleaning the oven
The website and diagram of my oven helped me know exactly what was wrong and where to locate the problem. I simply removed the oven door and the trim, pulled the oven out of the wall. After removing the back panel I located the part and put in the new part. Then reversed the procedure.
|