974727-1-S-Whirlpool-9759243           -Thermal Overload Safety Thermostat
974727-1-S-Whirlpool-9759243           -Thermal Overload Safety Thermostat 974727-2-S-Whirlpool-9759243           -Thermal Overload Safety Thermostat http://www.partselect.com/Schematics/Whirlpool/Whirlpool_Thumb/XA4HNFR4.gif

Thermal Overload Safety Thermostat

PartSelect Number PS974727

This part establishes and maintains the internal temperature of the oven cavity.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Little to no heat when baking.
  • Will Not Start.
  • Element will not heat.
  • Compare At

    $44.45
  • You Save

    $7.41
  • Your Price

    $37.04
In Stock
Order within the next 4 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.9 / 5.0, 9 reviews What's this?
1-5 of 9
 

75 of 83 people found this instruction helpful

Parts Used

  • Thermal Overload Safety Thermostat

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers

CustomerFrederick from St. Louis, MO

No heat after cleaning oven

This built-in oven was slid out of it's space and set on a box. I removed the back cover with nut driver and located the safety overload device. removed nuts and used pliers to remove wires and replace them. The power must be off to do this repair.Replaced the cover and slid back into place. This could be a lot more difficult if your power cord or gas line is not long enough to make it out of your wall space. Or of your oven is attached well to the frame.

Help other customers find the most helpful instructions.

Were these instructions helpful?

19 of 20 people found this instruction helpful

Parts Used

  • Thermal Overload Safety Thermostat

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerDevin from Platte City, MO

Oven wouldn't heat after cleaning cycle

Turned power to oven off. Removed trim screws and trim. Removed screws that anchored oven in cabinet. Removed oven from cabinet. Removed back panel, tested thermal fuse. Determined it was defective, ordered new part and reversed procedures above to reinstall.

Help other customers find the most helpful instructions.

Were these instructions helpful?

13 of 18 people found this instruction helpful

Parts Used

  • Thermal Overload Safety Thermostat

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerRobert from Willow Park, TX

Oven wouldn't heat after a cleaning cycle

Recieved the part promptly. From looking at the diagrams, we knew the overload thermostat was located on the back of the oven. We removed the screws, brackets, etc, slid the oven out, which for us was fairly easy as it's an under counter oven. Located the thermostat, removed it, replaced the new one, connected two clip wires, replaced the oven, turned the power back on and it works like a champ. Total cost was under 50 bucks.

Help other customers find the most helpful instructions.

Were these instructions helpful?

10 of 12 people found this instruction helpful

Parts Used

  • Thermal Overload Safety Thermostat

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerKenneth V. from Kent, WA

Upper oven bake and broil elements fail to heat when keypad entries made and indicating correctly

Replacement of the thermal overload safety thermostat very straight forward after sliding unit out, killing power and removing two covers. Tested both old and new and both show continuity (= good). Installed new, restored power and tested for proper operation. Didn't happen. Replaced original and now have new as spare. Now suspect the double line break relay on electronic control board is failed and source of problem. It is common to both elements and immediate before the suspected thermostat in circuit.

Help other customers find the most helpful instructions.

Were these instructions helpful?

10 of 12 people found this instruction helpful

Parts Used

  • Thermal Overload Safety Thermostat

Level of DifficultyReally Easy

Time to do repair:1- 2 hours

ToolsPliers, Screw drivers

CustomerElvin from Richmond, VA

Oven would not heat

This is a drop in range so I had to remove the range and set on a dolly. Turn the dolly around and acess the THRMST-FIX that needed replaceing, it was open. put the range back in its place and could still use the rest of stove until I received the parts 2 days later .
Pulled the range out put the new THRMST-FIX in put the range back together and put the range back in place and it has worked ever since.
GOOD JOB

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 9