| |
10 of 11 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers
CustomerMichael from Sewanee TN
Broken tray ring for rotation of dish.
Used needle nose to pull off piece of old ring. Layed in new one.
|
3 of 4 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerJack from Scottsboro, AL
Old roller piece broken
Took out the old, put in the new.
|
3 of 4 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerCesa Lynn from Montgomery TX
Turn table in the micro was broken due to the plastic 3 wheel mechanism that cracked. T
I could just set the new whirly gig in the bottom hole of the micro and it worked. The new part was delivered in 24 hours of my order and hence fixed in 24 hours. Thanks so much Part Select
|
2 of 4 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerJuan from Los Angeles CA
Turntable roller shaft was broken.
Put in the new part, took less than a minute...
|
2 of 4 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerCynthia from Wylie TX
Original rotater broke
Replaced the broken piece with the one purchased at Partselect.com. I was concerned that the part would not be correct since all we did was enter the model number of the microwave. PartSelect.com was really easy to use and sent the correct part. Thanks so much for making this process easy.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerYvette from Riverdale IL
My turntable wouldn't turn
I took the turntable roller guide, dropped it into the hole, put the plate back on the turntable roller guide; and voila!!! It worked!
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerJoellyn from Olathe KS
Stem broken off the turntable base so the turntable wouldn't rotate
Removed the broken plastic base that the glass turntable sets on and put in the new plastic base. Took 5 seconds max! The part arrived in about 24 hours! Great service!
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerDebbie from Franklin Park IL
Turntable stop moving
Replaced turntable support with new unit.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerKirk from Los Angeles CA
Turntable stopped turning
It seems that the heat of the microwave cracks the part over time. It is a very simple installation.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerJulie from Madison MS
Plate in microwave would not turn
took out plastic piece under plate (that was broken) and placed new one in the hole. No tools req'd. Works like new.
|
0 of 3 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:More than 2 hours
Tools
CustomerElizabeth from Horseshoe Bay TX
Fridge not cooling, freezer ok.
Ice covered the top back of the freezer compartment. This did not allow the cold air to move up to the fridge. Complete defrosting (36hrs) fixed the problem. There was a lot of water, from ice inside, that was not visible. We realized the freezer drawer must have been left cracked open. Thanks so much.
|