Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS972325
This kit includes 2 door balance links and 2 door balance mounts with wheels.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
Remove two screws then the two toe-panels. Use a flashlight to locate spring and the hole in the metal frame near back of unit about an inch off the floor. Look at opposite side of unit to see how the working link is routed. Place correct end of the link over one end of the spring and wrap a piece of tape around nylon clip and spring end (just to save frustration of having it fall off while you attempt to complete this task). Tie a loop in the end of each end of the piece of string you supplied. Loop one loop around the spring end with the link clip and feed the other end of the strings loop out the front of the dishwasher at the bottom near the lowermost pulley. Reach under the dishwasher and hook the spring to the frame. Keep tension on the string and feed the link cord out the front of the dishwasher near the front bottom near the lowermost pulley. Loop the exposed end of the self-supplied string around the center of the flashlight handle. Have an assistant pull firmly on the flashlight/string stretching the spring (not too much to over-stretch the spring, but give yourself a little slack too). Serpentine the link cord around the two nylon pulleys. Make sure the rope side of the link clip is toward the back of the dishwasher. Place the link nylon clip over the metal door lever and into the appropriate slot. Have your assistant slowly release tension on the spring/string. Reach under the dishwasher and remove the looped string from the spring end and remove the string. Replace the toe-panels. I did the right side this way, the left side is up against a wall and I might have had additional problems, but it is hard to say since I did not replace the left link. I thought this easier than removing the dishwasher, inlet and outlet as I have done that several times and it can be a pain as well. Good luck!
Help other customers find the most helpful instructions.
Were these instructions helpful?
Turned off power to dishwasher.Removed screws from dishwasher retaining clips.Pulled out dishwasher.Removed broken rope.Installed replacement and put everything back together.Very easy repair. The spring is very strong and extra hand can be helpful, but not required.
Followed the parts list diagram and confirmed with the link on the other side of door. Hooked the plastic attachment to the door, threaded the string around the plastic pulleys, attached the spring and mount it to the back of the dishwasher. that was it! Very easy to do. Hardest part was sliding the dishwasher out and in.
last time this piece broke, I called a tech and $150 to fix. I am not much of a do-it-yourselfer, but this was very easy. Removed to screws. I then pulled out dishawasher from cabinet. Removed plastic piece, replaced part, pushed dishwasher back and put in screws.Easy, easy, easy. Appliances use to be built with metal parts that did not break as often.
First I turned off the water and power to the dishwasher.I removed the two screws on the front bottom cover plate, removed the plate. Removed the two nuts and bolts holding the dishwasher in place between the cabinets. Then I pulled the dishwasher out about 6 to 7 inches so I could see the spring, pulley and rope connections. Then I saw the rope on the right side of the door bottom had pulled through the connector. I ordered the part and next day delivery was great.(excellent service). The repair kit comes with both sides parts but I only needed one(for now). I reconnected spring to rope connector and threaded through pulley and to the door and job was done. A little difficult stretching spring so I put a long piece of wire to hold spring tight while connecting to rope but I worked out great. My husband said "great job, honey". I saved a $150 repairman bill....now I might go shopping (ha ha) Kim
Removed 2 screws that held unit under counter. Slid diswasher out about half way; reattached metal spring in back and removed broken string. Attached replacement string to spring and threaded through wheels (copying other side), then attached string to door. Tada! Done. Will never pay a call-out fee again (for this problem anyway...)
After pulling the dishwasher out of the cabinet (2 screws held brackets to the underside of the counter - accessible when the door is open), I removed the broken link pieces, re-attached the springs and routed the link line around the pulleys. No need to re-set the spring tension as it was adjusted properly.Was able to download a PDF manual from Sears for the dishwasher, so had the necessary information in the event adjustments were necessary. I bought spare links as the dishwasher was less than 3 years old, and I expect them to fail again.
Disconnect top screwsPull dishwasher out halfwayNotice how the other side is connectedThread cord, use pliers to pull spring to connect.
Received the part. No instructions came with it. Luckily it was pretty simple to figure out. i removed the appliance from under the counter, saw how the part was attached on the other side and simply replaced the other side that was broken. Easy.
Thank you for letting me share my repair experience with you.I removed the two screws that hold the diswasher to the wooden cabinet. Lowered the leveling adjustment screws on bottom of unit, then slid out the diswasher from inside the cabinet. Then ordered the new lanyard. Waited one week day and the order arrived via mail. It has two lanyars and new rotating pulley assemblies for both sides of the door. I loosened the bottom screw on the old pully assembly and refitted the new pulleys in same location. (very easy). I then refitted spring to back of unit (with blue line toward front), then fitted the lanyard to the spring. Pulled lanyard thru the pulley. Had to have nice wife connect the other side of the lanyard to the post as I extended the spring on the side of the unit. We completed same steps on other side of the unit. After completing the door lanyard repair, I slid the dishwasher in the cabinet, re-leveled the unit with the front adjustment screw, then incerted the cabinet screws into the wooden cabinet. I feel this was quite a savings to us. Thanks to nice individuals on the internet and partselect.com, who provided excellent service to me....and my family. I also can see the end result of my effort, which is a nice feeling.Thank you.
The hardest part was pulling the unit out. Ours required the electric to be disconnected. First turn off breaker, then disconnect electric, then remove the 2 screws in the sides that keep it in place (located on top for non-stone counter). Slide unit out. Next remove the spring and connect the loop from the link to the spring. The other end of the spring goes in the hole next to the rear leg. Pull the string so there is enough slack to loop the spring aroung both pulleys and then slide the end over the hook on the bottom of the door. Use the other side as a guide. Slide unit back, hook up electric, replace mounting screws. Turn on breaker.
Shut off elec. and water. remove bottom plate and 2 screws holding the unit to the counter top.disconect elec wires to unit and remove water line.Pull unit out from counter and replace cable to spring the same way as the unbroken side.Slide unit back and reverse hookup. My only problem was that the part they sent me was about a 1/2" shorter the the original and the door is hard to open.
Removed the bottom cover plates.Removed the screws holding in the dishwasher.Removed old single moving roller and replaced with newly designed double rollers. Installed link(string).Replaced other side rollers and link.Reinstalled dishwaser.
The repair itself was relatively easy. I basically only had to remove the two screws that were securing the diswasher to the cabinetry, disconnected the water line and extended the diswasher out approximately 10 inches. I then replaced the part by hooking the new cable assembly to the spring and using pliers expanded the spring so I could snake the other end of the cable through the pulleys and attach it to the door. The otherside was my guide. This part should be modified to replace the two plastic ends with metal counterparts. This would allow the part to have a longer life especially in my case since the plastic end broke and not the cable itself.
First we removed the two screws up under the countertop that secured the dishwasher in place. Next we pulled the d/w out from under the counter, having to unplug the power cord and feeding the drain hose into the d/w cavity from under the kitchen sink to allow this. On each side, attached to a metal spring was a nylon cord with plastic attachments that ran through two plastic pullies/wheels. The plastic piece on one of the nylon cords had broken...only on one side, so we were able to just look at the 'good' side to see how to attach and string the repair part through again. We pushed the d/w back in, made sure the drain hose under the kitchen sink wasn't kinked by pulling it back under the sink from the d/w cavity, plugged it in, replaced the two securing screws and were done. The old cord running through the pullies had always creaked when the door was opened, so while the d/w was out, we coated it w/ WD40. Piece-of-cake!
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.