| |
14 of 16 people found this instruction helpful
Parts Used
-
- Lower Dishrack with Rollers
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerCarol from Richmond Hill GA
The old rack was rusty leaving stains on our china
The new rack came with four parts... those four parts were the wheels that the rack rides on to slide it into the dishwasher. You will need to recycle two rubber bumpers, your old utensil basket and the cone in the center of the rack. Getting the cone free was not easy. It has to be rotated to release it from the wire rack. I had to pry it free with a screwdriver. Once rotated it lifted out easily. I noted how the cone lined up in the old rack and installed it the same way in the new rack. It was much easier to install than remove. The new rack has a gray tinge to it but fits perfectly and we are pleased with the end result.
|
11 of 17 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
Tools
CustomerAnthony from Highland Lakes NJ
Replaced upper and lower racks
Easy. only one little trouble spot. but very easy " repair" for the lower rack. take out of box. place in dishwasher. pull old center spindle part off by twisting 90 degrees and put into new rack same way. When replacing the top rack. keep the old one in one piece till you put together the new one. mine didn't come with any instructions. pretty simple anyway. but no problem when you can use your old one as a guide. once you put it together the only hard part i had was right at the end.. figures right!! last piece.. but to snap back in the center unit the spins around into the new one took alot of force. but it went. thats it...
|
4 of 10 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:30 - 60 mins
ToolsPliers, Screw drivers
CustomerAllen from Jacksonville NC
Replaced old dish racks that had rusted and had broken tines.
Took the old wheels, and other parts from the old racks and installed them on the new. The wheels on the lower rack just snap on. Also the folding tines just snapped on. On the upper rack the brackets that hold the wheels have two screws that hold the bracket. I removed them and then installed the bracket on the new rack in the same position as on the old one. The only hard part was getting the old spray arm off the old rack. I had no directions so I had to figure it out for myself. I finally cut the the old rack to get the pressure tower off. It was stuck because of having been in place for more than ten years. Putting the tower and the arm on the new rack was no problem once I had it removed. Total time to do the job about 45 minutes.
|
1 of 2 people found this instruction helpful
Parts Used
-
- Lower Dishrack with Rollers
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerChris from La Center WA
Original lower dish rack was falling apart.
Took out old rack, put in new one. Part arrived on time and was an exact match to the original.
|
1 of 2 people found this instruction helpful
Parts Used
-
- Lower Dishrack with Rollers
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerDonna from Hicksville NY
Old dishrack was rusted and chipped
Removed old rack opened box inserted new rack. So simple sorry I waited so long to replace.
|
2 of 5 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:30 - 60 mins
ToolsScrew drivers
CustomerLeo from Pitman NJ
Racks had broken tines in racks
It was simple just took out the racks and used them as model. Placed new rack side by side, opened bag and laid parts out for new racks. BY looking at old it was easy to put together. New racks work like a charm.
Thanks for being there it saved me having someone come out and/or just buying a new one when ther was nothing wrong withthe old one.
|
1 of 2 people found this instruction helpful
Parts Used
-
- Lower Dishrack with Rollers
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerRichard from Middletown MD
Dishwasher was leaving rust spots on the dishes. The lower dishrack plastic had worn away in places leaving bare metal exposed.
Just removed the old lower dishrack and set in the new one. Nothing to it.
|