Quick Question!

Have you ever purchased from PartSelect.com before?

972314-1-S-Whirlpool-8193951           -Impeller and Seal Kit
972314-1-S-Whirlpool-8193951           -Impeller and Seal Kit 972314-2-S-Whirlpool-8193951           -Impeller and Seal Kit 972314-3-S-Whirlpool-8193951           -Impeller and Seal Kit http://www.partselect.com/Schematics/Whirlpool/46WLNAIP.gif

Impeller and Seal Kit

PartSelect Number PS972314

The impeller threads to the motor shaft.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Not cleaning dishes properly.
  • Leaking.
  • Noisy.

Compare At

$33.30

You Save

$5.55

Your Price

$27.75
Order within the next 8 hrs and your part ships today!
Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.5 / 5.0, 4 reviews What's this?
1-4 of 4
 

59 of 98 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver
Customer: Chauncey from Menan, ID

Started with a grinding noise in the bottom of the dishwasher, and then the thing just stopped cleaning the dishes. It wasn't pumping any water,

I removed the plasic inner parts, used the torx drivers to remove the internal platic plate that covered the sump. Found the food chopper cover and removed it. It had gotten a piece of plastiic wrapped around it. As it spun it had ground the teeth off the end of the drive on the impellor and the food chopper. I replace both as a set and it works fine.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

25 of 31 people found this instruction helpful

Parts Used:
  • Impeller and Seal Kit
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Screw drivers, Socket set
Customer: Kathryn from Gordon, NE

Dishes would not clean

Checked grinder and cleaned it several times, adjusted blades. Dishes would be clean for approx. 6 cycles, then would not clean. Placed dishwasher on its front and removed the motor. Removed grinder and impeller which I found to be worn so that the blades would not turn on the grinder which caused it to collect food particles. The impeller locks in easily.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

14 of 18 people found this instruction helpful

Parts Used:
  • Impeller and Seal Kit
Level of Difficulty: A Bit Difficult
Time to do repair: More than 2 hours
Tools: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Customer: Jerome from Greensburg, IN

The ceramic seal had failed, allowing water to destroy the front motor bearing.

Removed dishwasher from under the counter and took it to my shop. With the washer on its side, I removed the motor, then the impeller and seal. I then disassembled the motor and replaced the front bearing(purchased separately). This required an arbor press. I then reassembled the motor and installed the new seal and impeller. Reassembled in reverse order. Reinstalled under the counter and made conections. Checked for leaks and proper operation.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

13 of 26 people found this instruction helpful

Parts Used:
  • Impeller and Seal Kit
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Nutdriver, Pliers, Socket set, Wrench (Adjustable)
Customer: Gerald from Simsbury, CT

Dishwasher would not pump water

.The easiest way to complete the impeller and chopper motor replacement is to disconnect the power, water and drain line, remove the dishwasher from the cabinet, set the washer on its back.

From this point everything is visible, pump housing, motor, etc. and it's a matter of disassembly and reassembly. Make note or a drawing of where all the wires are connected so you reconnect them in the right spots.

Reinstall water lines and power and check for leaks before replacing shield or kick plate.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-4 of 4