Quick Question!

Have you ever purchased from PartSelect.com before?

964304-1-S-GE-WR17X11653        -Dispenser Door Assembly or Flapper
964304-1-S-GE-WR17X11653        -Dispenser Door Assembly or Flapper 964304-2-S-GE-WR17X11653        -Dispenser Door Assembly or Flapper http://www.partselect.com/Schematics/GE/00120714i01.gif

Dispenser Door Assembly or Flapper

PartSelect Number PS964304

This part mounts in the ice dispenser. **** The crank no longer comes with this part. You can use original crank. The crank is sold separately depending on model number of appliance.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Door Sweating.
  • Ice maker won’t dispense ice.
  • Leaking.
  • Frost buildup.
  • Not dispensing water.
  • Freezer section too warm.
  • Door won’t open or close.
  • Freezer not defrosting.
  • Ice maker not making ice.
  • Ice maker dispenses too little ice.

Compare At

$11.74

You Save

$1.96

Your Price

$9.78
Order within the next 3 hrs and your part ships today!
Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.6 / 5.0, 55 reviews What's this?
 

1 of 2 people found this instruction helpful

Parts Used:
  • Dispenser Door Assembly or Flapper
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: Kyoko from Bellevue, WA

Frost/ice buildup in icemaker chute in the freezer door

The only difficult part was not knowing which parts had to be removed to gain access to the flapper to replace it. It appeared as if the frame around the control panel would have to be removed as well as the door handle; we tried but were not able to remove the frame. It turned out that the panel just popped out with the frame in place. Once we had access to the flapper, it was easy to replace it. The repair fixed the problem.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
  • Dispenser Door Assembly or Flapper
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Al from River Edge, NJ

Ice maker discharge was slow and jammed with ice and frost. The cause was a distorted flapper that did not seal properly, admitting warm air into the dispenser chamber.

Excellent video was available on the Parts Select website. It was simple. The selector panel pulled out by hand from the bottom. The subpanel was removed with the four screws. The flapper snapped out of the holder with two clips. The new one was inserted in reverse order.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
  • Dispenser Door Assembly or Flapper
Level of Difficulty: Very Difficult
Time to do repair: 1- 2 hours
Tools: Pliers
Customer: salomon from dallas, TX

Flapper gaskeet dried out

The video to replace the flapper looks easy, howerer the first step is to remove thestic cover of the icemaker. In my refrigerator model (as oposed to teh one shown n teh video) teh coved if firmly attached and goes under the refrigerator external plate so I was never abel to take it oot (so step 1 failed).
I was able to replace the flapper TROUGH the whole whre te ice comes from! this took lots of patients and someone with small hands!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
  • Dispenser Door Assembly or Flapper
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Roger from Colleyville, TX

No water through door dispenser

Replaced flapper valve per website instructions. GE factory technician took two weeks to get here, charged over $100 for the call and told us we needed a new refrigerator door at a cost of over $500 to fix the problem. We sent him packing. After visiting the PartSelect website, the $5.88 PartSelect flapper valve fixed the problem. Amazing.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
  • Dispenser Door Assembly or Flapper
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: George from HOSCHTON, GA

Frost collected in the ice dispenser shute clogging it

Replace the flapper and this solved it. The video provided was excellent and allowed me to do this repair myself.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
  • Dispenser Door Assembly or Flapper
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: joselito from riverview, FL

Ice building up in the ice dispenser chute

Under the control panel there are three small holes. Insert ballpen or small flat screw driver on both outer holes to push a tab lock that holds the control panel in place. Then pull out control panel and three set of wires will be exposed and disconnect wire connectors (connectors have different sizes so you wont get confused in reconnecting). Unscrew four screws on each corner that holds the ice dispenser assembly (a part where you push your glass against to dispense ice or water. The flapper is exposed and easy to replace.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 5 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Victor from Houston, TX

The compartment behind control panel with snow

This time I did not make repair. I have purchased only to have spare parts. I have changed this parts recentely and I think this parts are not strong enough to work more than two or three years.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
  • Dispenser Door Assembly or Flapper
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: GARY from LIVONIA, MI

Ice maker clogging up from frost build-up

Turn off power
Remove operator faceplate by pullling out on outer lower corners
Disconnect wire connectors from circuit board
Remove four screws from dispenser and pull out dispenser assy
Replcae Door ASsembly
Put everything back in place
Power up
Job Done

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: john from Sicklerville, NJ

Ice damming and freezing blocking dispense door

I unplugged the unit and removed the modeling around the beverge center on the exterior door. At this point I was able to remove the face place to the icemaker and gain access to the ice maker doors csrews. I unscrewed them and replaced them with the new part and reassembled in the reverse order. Generally an easy fix for a poor design for novice handy man/women...

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 1- 2 hours
Tools: Screw drivers
Customer: Richard from Bradenton, FL

Icemaker door wouldn't close properly

Removed front panel and control touch pad to access solenoid and door recess assembly.
Replaced solenoid and door recess assembly. Didn't need spring and crank door.
Wish you could have supplied new screws, as the original are very corroded and I can't find them atv any hardware store.

Thanks

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
  • Dispenser Door Assembly or Flapper
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Ken from Wesley Chapel, FL

Froze in freezer

unclipped and replace with new part.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 3 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Charles from Waterford, MI

Ice dispenser wouldn't work.

I watched the video and armed with that information and a few inexpensive parts replaced the defective solenoid, flapper and crank arm. I'm pretty handy and this was easy! I discovered quite a bit of mildew up and behind the panels and was able to clean those panels completely while they were removed. The screw heads were a little rusted so I made sure to use a new Phillips screw driver with the exact size tip and some moderate finesse to loosen or remove the screws. I will return to Parts Select in the future for any appliance repair parts. Thank you!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 3 people found this instruction helpful

Parts Used:
  • Dispenser Door Assembly or Flapper
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Robert from North Topsail Beach, NC

Ice dispenser chute icing up

Replaced dispenser flapper

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Bill from Venice, FL

Ice maker dispenser chute frosting up

Before starting my repairs I checked for part suppliers online. Partselect was one of the first I saw. They also had instruction videos. After watching the video, I took apart the ice maker and found the solenoid had rusted. I replaced the solenoid and while everything was apart I replaced the crank, spring and the flapper. The entire process only took about 20 minutes and that was only because of their informative videos.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Dispenser Door Assembly or Flapper
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Screw drivers
Customer: JAMES R. from INDIAN SHORES, FL

Moisture seeping into freezer through ice dispenser

Removed ice dispenser trim from bottom-up and then removed control panel by gently pulling up from the bottom. Removed four screws holding dispenser chute and then two screws holing flapper assembly. Replaced gnarly old flapper with a new one and put all removed pieces back together.

Help other customers find the most helpful instructions.

Were these instructions helpful?