Quick Question!

Have you ever purchased from PartSelect.com before?

964304-1-S-GE-WR17X11653        -Dispenser Door Assembly or Flapper
964304-1-S-GE-WR17X11653        -Dispenser Door Assembly or Flapper 964304-2-S-GE-WR17X11653        -Dispenser Door Assembly or Flapper http://www.partselect.com/Schematics/GE/00120714i01.gif

Dispenser Door Assembly or Flapper

PartSelect Number PS964304

This part mounts in the ice dispenser. **** The crank no longer comes with this part. You can use original crank. The crank is sold separately depending on model number of appliance.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Door Sweating.
  • Ice maker won’t dispense ice.
  • Leaking.
  • Frost buildup.
  • Freezer section too warm.
  • Not dispensing water.
  • Door won’t open or close.
  • Freezer not defrosting.
  • Ice maker not making ice.
  • Ice maker dispenses too little ice.

Compare At

$11.74

You Save

$1.96

Your Price

$9.78
Order within the next 8 hrs and your part ships today!
Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.6 / 5.0, 55 reviews What's this?
46-55 of 55
 

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Larry from Harkers Island, NC

Ice keep coming out when the funnel ice display was push in to get ice

Pulled the front panel off and let it hang by the wires, removed 4 screws replaced the new funnel ice display and spring works great.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Dispenser Door Assembly or Flapper
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: HERBERT from Harlingen, TX

Gasket was shot

took off the panel, took out 4 screwws, took out old flap, installed new flap, put screws back in , and put trim back on.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: DSavid from Bristol, CT

Ice door was not closing fully

I followed the video that was posted in the section. It was very helpful. I wasn't sure on how to remove the panel and the video explained it completely.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Dispenser Door Assembly or Flapper
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Jason from zion grove, PA

Rubbeer flapper was worped causing frost in the freeze

The same as the vidio, very easy. Thank you

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Dispenser Door Assembly or Flapper
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Thomas from Arlington Heights, IL

Frost on the bottom of the ice bin frome warped rubber flapper

Pulled the outter cover off, removed the electronic board, replaced the flapper and put it back together again.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Dispenser Door Assembly or Flapper
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Richard from Atlanta, GA

Frost was building up inside the freezer just above the ice dispenser shute.

Followed the instructions and replaced the door recess.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Dispenser Door Assembly or Flapper
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Dana from Pittstown, NJ

Ice chute from the ice maker frosted over. Cubes would not dispense

1. Unplug the fridge
2. Removed the outer facing of the dispenser outside the freezer door. This is fairly easy, better with a tool (plastic scraper) that won't mar the finish.
3. Removed the plastic plate with labels -- water, ice, etc. This is done by sliding a small jewelers screwdriver into the slots on the left, middle and right in back of the plate. These are difficult to see without a flashlight.
4. Removed the four screws in the panel behind this plate.
5. Unpluged the large cable on the left side after the panel is freed.
5. Removed the rubber "dispenser" button. this just pulls off.
6. Remove the panel
7. Lift flapper up and remove. Clips hold this in.
8. Put new flapper in place.
9. Use reverse order to put back together.
Piece of cake. Ice maker no longer frosts up.!!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Difficult
Time to do repair: 1- 2 hours
Tools:
Customer: GUILLERMO from GILBERTS, IL

Frozen ice door maker

order the flopper, spring and racker can`t replace them; becouse factory recall back on 2003 most replace two ft. door of refrigerator. for $400.00

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Justin M from Cypress, TX

Ice door gasket warped would not seal

Pop off the control board for the ice selector/water. Remove power / signal connections. remove four phillips screws, Remove plastic hopper. Pop off Ice door gasket, pop in new one and put back together. If you fridge was sounding like it was speeding up and slowing down, this will correct this problem as well.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 3 people found this instruction helpful

Parts Used:
  • Dispenser Door Assembly or Flapper
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Earl from Franklin, NC

The door recess asm would not seal tightly

remove the 'pop-out " frame around the door recess, you pry the flexable seal from around the ice despenser, have someone hold the unit with the wiring, remove the one screw that holds the door recess, and replace the new one. reverse the procedure. remember to unplug thr frig. first

Help other customers find the most helpful instructions.

Were these instructions helpful?   

46-55 of 55