| |
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerPamela from Mouth Of Wilson VA
The drum bearing and slides worn out
The dryer literally ate my clothes!! We took the front cover off the dryer, removed the old parts and snapped in the bearing, felt seal and slides and now it just dries....it doesn't eat anything.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerJeanne from Owensboro KY
Screaching
I have always been mechanically inclined so when my dryer started making noise I turned it into a family project. I found your website and studied what could be the problem. My 13 year old son and I took the dryer apart and found that it was the front drum bearing. i ordered the parts and my son did most of the work. Only had to take out two screws holding the top on and two holding the front. Vacumed out lint and followed directions on your site to replace parts. up and running in about 30 minutes.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsScrew drivers, Wrench(Adjustable)
CustomerLaurie from Lawrenceville GA
Very loud noise.
Took the front & top off the dryer. Saw that the slides were missing or broken. Got the parts and put it back together. Works great.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerLinda from The Woodlands TX
Had difficulty finding the correct size in any store.
All the stores had either a smaller watt or a larger watt and the book suggested always using the correct watt. I was glad to find it on this sight and it was delivered very quickly.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerMike from White Cloud MI
Dryer sqeaking
remove the 2 screws going into the top, remove it
remove the 2 screws going to the front panel, set it aside install parts and reverse order. very easy to do
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:More than 2 hours
ToolsScrew drivers
CustomerKen from Neenah WI
Sqealing sound during operation
Disassembled and removed drum according to directions on this site. Ordered parts and replaced per instructions - - easy as unscrewing and rescrewing old bearing assembly. Hardest thing was putting the belt on - as I did it fromthe front side and the recommendations are to access from the back kick plate. I did not want to wreck the vent tube so I left the dryer in place and did the entire job from the front.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerTerry from Brandon MS
Dryer was shaking and vibrating all over the floor
Took top and front panel off. Pulled top bearing shroud off, replaced and installed the slides on new top bearing. Installed felt gasket on the bottom piece of lower shroud. Installed new lamp and put back together to check out. Dryer working great now. Should have changed the belt but it is not squelling so it is fine.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsNutdriver
CustomerJoseph from Cedar Park TX
Broken on/off switch and drum light burned out
Losened four hex screws to open up control panel assembly, removed and replaced threee wires from switch with new swithch, re-assembled control panel. Removed old bulb and replaced with new one. All worked well.
|