Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS960316
Note: The drum slides should also be replaced when your replacing the drum bearing.
Slides are NOT included. This part helps your dryer operate as quietly as possible.
This part works with the following brands: GE, Hotpoint & Kenmore.
This part fixes the following symptoms:
Sold individually. There are 2 per dryer. They attach to the outer-most sides of the bearing. Manufacture recommends to replace both slides at the same time.
I followed the instruction of the first posting for this category and it worked perfectly...thanks for the nice detail...- Upon receipt from PartSelect, placed new slides in Drum Bearing (this does not come together or as a kit - must order 4 slides AND Bearing separately for this dryer model)- Loosened Top panel screws (2) from inside door area - Slid top of dryer off - PAY attention to HOW the top comes out (tabs at the back and slots on the sides) or replacing the top could prove frustrating)- Loosened Front panel screws (2) and GENTLY leaned the panel forward to access Drum Bearing - no need to REMOVE the front panel but be aware of the switch wires when leaning and the weight of the door if you did not remove that - Removed old Drum Bearing- Vacuumend interior of dryer cabinet (especially area leading down to vent)- Snapped new Drum Bearing into place- Re-secured Front panel paying attention to drum position to make sure everything still rotated properly and freely- Reset Top panel - align back tabs first, gently pull forward just a bit until Top slips down over side tabs, then slide back into place and re-secureWorked like a charm - took about 20 minutes...
Help other customers find the most helpful instructions.
Were these instructions helpful?
Read the other posts - they are very good. On my particular dryer it took two Slide WH and two Slide Dryer Drum Side PS266785. Most time spent was vaccuming out and removing a softball size ball of lint clogging the dryer - now it will actually dry clothes! Part select delivery is really fantastic (even though it took me three orders to get it right!).
Unplugged dry cord . Removed top and front cover. Removed drum to replace rear Bearing. Reinstalled drum replaced front bearings and sleeve. Reinstalled both covers and plugged in.
Many have already described the repair, and it was exactly as they have described. Remove the two screws inside the top of the opening which hold down the top of the dryer. Pull off the top, and look inside to remove the two small screws that attach the front of the dryer. As the front separates, the front comes out of the drum and the drum bearing will come into view. Pop out the drum bearing ~ there are no screws ~ it simply snaps in place. (I suggest removing the lightbulb first, or you'll be buying one of those also. ) Replace the new drum bearing and snap it into place. Then replace the four drum slides. Replacing the drum slides is a quick, one minute task. Mine were completely worn away ~ no wonder it was squealing so badly. Then reverse the process to put it all back together. Total job was maybe 15 minutes long. Easy as could be and saved a ton of money, I'm sure. Sounds like new now!Piece of advice that I could not find anywhere prior to ordering ~ you need FOUR drum slides to replace them all. Not knowing, I originally only bought two, so I had to order two more and add them later. Also, I probably could have gotten away without replacing the drum bearing ~ the slides were all that was really worn.Thanks for the quick turnaround on the orders and the advice on line. Easy, easy, easy!
To quiet the noise temporarly I would spray silicone into the dryer drum groove on the front inside panel.Got tired of this and removed the top of the dryer by removing two screws under the front bottom of the dryer top. Remove two screws, one on each side of front panel(screws are on the inside). Lift the front panel straight up and swing to the side. Keep the wires connected to the panel. There is plenty of room to move panel about. Note: I replaced the drum bearing thinking it was a one piece unit with the teflon rub strips. All I had to do is order the teflon rub strips and I would have saved 24 dollars. Reverse the disassembly process to assemble.
A quick look inside verified that the drum slides were worn through but I also found that the plastic drum bearing that holds the slides was cracked in a couple different places. Ordered a new drum bearing, new slides, and decided to replace the felt seal as well since it looked pretty ratty. Parts arrived quickly after ordering and installation literally took 15-20 minutes. Purrs like a baby now. Steps: Unplug dryer. remove two screws which hold top of dryer to front. Remove two screws which hold front (door) to rest of unit. No need to disconnect wiring to front door, just make sure not to pull the wires out! Install new parts. Put it back together in reverse order.
I removed the top of the dryer by removing two screws located under the front lip of the dryer over the dryer door. Then I removed the dryer door by removing the screws holding the hinges. I then removed the front panel of the dryer by removing the two screws at the top inside two corners. I the removed the old Dryer Drum Slide. The Drum Bearings were almost completley worn off. I installed the (4) new Drum Bearings (2 Clear or White and 2 brown) the same way they were installed on the old Dryer Drum Slide on the new Dryer Drum Slide. I then installed the Dryer Drum Slide the way I removed the old one. Then I pulled the old Lower Front Drum Seal-Felt and replaced with the new one. Works like new!
First, I removed the 2 screws for the top panel, lifted the top panel off, then I removed the 2 screws holding the front panel, tilted it forward to clear the drum, disconnected the door switch and set the panel aside. I then installed the 4 slides on the new front bearing, removed the light socket from the old bearing, removed and discarded the old bearing. I installed the light socket into the new bearing and the bearing assembly snapped into place on the front panel. I then re-connected the door switch, aligned the front panel with the drum, secured the front panel with 2 screws, then carefully placed the top panel back in place and secured it with 2 screws. I checked the rotation of the drum and it worked like a champ. Matter of fact, that same day I put this dryer and a matching washer up for sale at 8:30 am on October 31st and by 9:20 am I already sold them!! I delivered and hooked them up and the dryer works great!!!
I had already replaced the four (4) small wear strips which were like short strips of teflon, and the squeaking decreased almost completly. I noticed that front side of the drum itself had started to wear through the actual plastc drum bearing, but I hoped having previously replaced these tefon strips that would be the overall fix.Wrong again... after a few weeks the squeeking continued until I ordered the new drum bearing and replaced the worn one with the new one. I was able to re-use the previous teflon wer strips, and it's like new now at least the squeaks are gone,The actual fix was a very simple remove old drum bearing, snap in new drum bearing install old teflon wear strips put four screws in top, and front panel and I was back in business
After several weeks of my wife and kids complaining about that monster in the other room squeaking and jumping around eating all of their clothes I decided to investigate. I removed the plug in from the socket, pulled the dryer out a few feet and decide to follow the instructions I had come across on my iPad, the videos that were listed on parts select were very helpful to watch as I started the repair job, I removed the bad components as instructed in the video, looked up my part numbers on parts select web site and placed the order. Wow within 2 days my parts had arrived and I was ready to reassemble the dryer. That task was very simple thanks to those videos, I was so surprised at the amount of detail that was given, even looking at the parts assembly diagram was very detailed, the repair was completed in no time, with in 45 minutes the parts were installed and the dryer was plugged back in and ready for a test run ! My wonderful wife and kids were so happy to see that daddy had tamed that monster and the clothes would no longer be eaten by that big white monster, they jumped for joy!!!! Every one was happy once again!!! It was so simple a cave man could do it Thanks to you parts select we saved money on a service call, saved money on the parts, and most important that monster will no longer jump around squeaking and yelping and begging for more clothes hubby says, parts select your the best!!!! Thank you Roger Ozbun
-- Unplug dryer from electrical outlet-- Open Door-- Remove two screws going up into the top panel-- Remove top panel-- Close door-- Remove two screws holding front panel -- Remove Front Panel by turning out, keeping left side close to unit since wires are still connected.-- Vacuum out all loose dust/lint-- Tilt old Drum bearing toward you to remove.-- Remove Old Felt Drum Seal-- Install drum Slides on new Drum Bearing-- Install new Drum Bearing, make sure it clicks into place securely.-- Install new Felt Seal, make sure to push in far enough to securely hook to the clips on the bottom of the Drum Bearing.-- Reinstall front and top panels-- Plug in electrical -- Dry
I read the other repair instructions on this site and looked at the parts diagrams. It wasn't entirely clear how everything came apart but once I started by unscrewing the top of the dryer and removing it (screws were just inside the dryer door) it was easy. Unscrewed the front panel next , swung it out, and it was quick work to install the new bearing with the slides. It wasn't too clear in the parts diagrams but I did need two each of the dryer drum slides and front dryer drum slides, four total, two on each side of the drum bearing. The dryer had been running on the old drum bearing itself, the old slides had worn completely down and the bearing itself was starting to disintegrate too. If I'd caught it sooner I could have reused the bearing and just replaced the slides. Saved a lot of $ and the dryer is nice and quiet again!
Removed top - 2 screws. 2 more and the front comes off. I left the wires connected, and leaned the front against the wall. I then popped the drum bearing, with the slides off of the front, and pulled the felt from the lower half. I took some extra time cleaning lint with a shop vac. I then assembled the new parts back onto the front, and pulled the felt into position - it was a little fussy getting it right. The front panel and the top go back, and it`s done. I am glad I ordered the drum bearing, as the felt was worn much more than I would have guessed. This job could probably be done in 15 minutes next time, not including lint clean-up.
Removed top panel giving access to drum and screws that hold front panel (door). Removed to screws to be able to remove front panel but be careful wires are short not giving you much room to remove panel. Removed plastic Drum Bearing and replaced with New one. Installed slides and put back together.
Drum was misaligned and scraping againt the appliance housing due to worn-out slides.Replaced the drum slides 2 - white, 2 - black. Replaced the slide housing (front drum bearing?). This part was worn due to worn-out slides that were missing.Cleaned out old lint from rear of drum and appliance housing. Put new weather stripping seals on the lint catch exhaust. Checked drum belt for cracks and checking. Buttoned everything back up and dryer works as good as new. $60.00 for parts, 1 hour labor and the job was done!
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.