Burner with Igniter

PartSelect Number PS952996

The igniter does not come with wire nuts. *** Please NOTE: The igniter connector may need to be cut off and wires spliced to the range wiring with the porcelain wire nuts.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Little or no heat when baking.
  • Gas igniter glows but will not light.
  • Compare At

    $85.91
  • You Save

    $14.32
  • Your Price

    $71.59
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.0 / 5.0, 5 reviews What's this?
1-5 of 5
 

104 of 169 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsNutdriver, Screw drivers

CustomerEdward from Pipersville PA

On thankgiving day with company coming and the turkey in the oven, my kenmore stove decided to act up. The oven burner started to smell awful and start carboning up due to improper burning at the burner tube. We then abandoned our attempts to roast the turkey in the oven for that day.

After removing the bake tube and ignitor assembly the following day for a close inspection which involved removal of the bottom pan, racks etc. and disconnecting the ignitor / tube assembly by unscrewing the sheet-metal screws holding them in place, I discovered that the ignitor had burned a hole in the bake tube which could not be seen without unscrewing the ignitor from the tube first. This caused the air / propane ratio to dramaticly change causing the oven to have a strong odor, start to carbon up the bake tube and effect the temperatures and cook time and the possibility of monoxide fumes effecting the chef. The parts that partselect.com supplied, which were in stock ,worked perfectly and saved my Christmas goose. Happy Holidays!

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 8 people found this instruction helpful

Parts Used

  • Burner with Igniter

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsPliers, Wrench set

CustomerMatthew from Goshen IN

Oven burner was burned out, wouldn't light

Pull plug and shut off gas! The lower oven burner is held in with two rear and one front screws. I removed the top floor of the oven (two hand tightened screws at the back), the bottom drawer, and the front door (just lift it off the hinges). This allowed me to access the burner, and I removed it by unscrewing the three screws, unhitching the igniter connector, and lifting the burner and igniter up and out. I connected the new igniter on the new burner before installing it in the oven, and found that the connector did not match (I was warned about this possibility on the PartSelect site), but instead of splicing the wires together, I cut off the connector on the new igniter and replaced it with the connector of the old igniter. Then I screwed the burner into the oven, recoupled the connector, replaced the floor, drawer, and door, and I was done! It took about 45 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Burner with Igniter

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsPliers, Screw drivers, Socket set

CustomerJames from Hayden ID

Igniter was bad and tube wasblown

repair was easy enough, but the kit came with female ends and needed mail ends. I had to splice old connecters to new igniter

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 13 people found this instruction helpful

Parts Used

  • Burner with Igniter

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerCharlotte from Rochester PA

Oven would glow but the burner would not come on

My son took out the old burner bar and there was a hole burnt right through it. I ordered the part on Weds night and was surprised when we received it so quickly on Fri morning. He had no trouble at all - just removed the old igniter and bar and replaced it with the new one. Nothing needed cut or spliced - perfect match. Now I can bake again!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 4 people found this instruction helpful

Parts Used

  • Burner with Igniter

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers, Wrench(Adjustable)

CustomerThomas from Columbia TN

Burner had a hole burnt in it, glow plug broken

Removed burner and replaced

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 5