Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS9495545
This gasket goes on the bottom of the dishwasher door.
This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.
This part fixes the following symptoms:
First I opened the door all the way. Second I reached down to the bottom gasket then grabed it on the right end of the seal that is on the right side of the door. Then I pulled the end outward from the bottom of the door toward the heater coil in the bottom of the washer. It came out real easy. You see it just snaps into a little plastic groove under the door. I then cleaned up the area for food and soap particules. I then placed the new gasket in place by lining up the notch toward the right end with the piece of plastic that encloses the right end of the plastic notch on the bottom right end of the door. Then push it in untill it stops going into the notch. It snaps in but does not make a snaping sound. It just won't go in no more.
Help other customers find the most helpful instructions.
Were these instructions helpful?
Received the part 3 working days after order. Part was exactly like the original.Removed the door. Slipped off old gasket and replaced with new gasket. Replaced door and tried rinse cycle. Worked perfectly.
The strip comes right out when you pull, there is a space to grip it on the left and pull it out. The notch goes on the right side when you put it back in; it only goes in one way. I didn't get it all the way in the first time and closed the door; the gasket came right out. A clear sign that I had done something wrong! So I put it in again, this time pushing it as far as it would go. It went all the way in and stayed. It doesn't click or anything, but you can kind of feel when the notches all connect. Also, it doesn't slide right out again.... very easy!
With the door wide open and lower dishtray out, I pulled the old gasket out of its channel. I cleaned the channel with a rag and replaced it with the new gasket. It needed to be trimmed about an inch in order to get the door to close properly. Took me about 5 minutes. Then I removed the old bottom door gasket. Just grasped the plastic edge showing while the door is completely open. Pull outward with fingers moving toward the heating element. Cleaned this area also. Took the new gasket with notch on the right hand side of the dishwasher and pushed it into place. If you get down and look closely, you can see where the notch hooks up. The rest of the piece just slides in after that. Hasn't leaked since! No leaks AND no service call fee. Parts came super fast! So glad I found this website. I'm a housewife, you can do this!
Thought the problem was a faulty door gasket (there was a gap in the middle of it) so I ordered new(new one had a gap also) replaced it anyway - maybe it was worn out? Still leaked! Had to sit and stare at it and cycle it through. finally realized the spray arm had a hole in the end that was spraying directly into the gap in the door gasket. Hot glued the hole and it stopped so I bought a new spray arm - no leaky!
It took less than a minute to remove the old bottom door gasket - it pulls right out. You wouldn't think the part looks the way it does (a 1.5 inch wide plastic strip that runs the length of the door with rubber gaskets on both ends) but have faith. Trust the diagram/picture - it is the correct part and will fix the leak. The new gasket arrived within a couple days of ordering and was simple to install - no tools. It slides into place in less than a minute and is held in by friction. Problem solved and no more leaks. For under $12 (parts and shipping) I had my dishwasher fixed. A service call by itself would have run $75 - just for someone to show up at the house, and then probably another $50 for parts and labor to install. My wife made the comment "Even I could have fixed that". A very simple and easy repair - you can do it!!!
1. Bottom door gasket removed very easy by grabbing left corning and pulling out. Starting with notch on right side, slide the hard plastic side up at a slight angle to catch the slot the gasket will seat in. Slowly moving toward the left, push gasket into seated position. Notch in gasket will make sure it is in correct position. Push gasket all the way in so that it is flush with bottom edge of door. Watch when first sliding gasket in, it has to g at a slight up angle or it will fall into an empty space.2. Remove Tub gasket by gripping one side and pulling out. Replace in same fashion making sure the angled wedge of gasket is first part that lays flat in slot. Working from one side to the other, make sure the gasket seats completely. Trim excess if necessary.
I removed the dishwasher from the cabinet space (two screws) and manually replaced both springs. I replaced one spring first to see if there would be an improvement when the second new spring was installed. There was much better tension once the second new spring was added.That is why changing both springs is recommended. This was very easy.Changing the gasket was scary because I thought the the whole door would have to be taken apart. You know nothing ever goes back together the same. I feared that I would create an even bigger leak than what I had. Taken the door apart didnt work for me, so I just pulled the old gasket by hand and pressed in the new one. I made sure that it was seated correctly. Voila no leak. The dishwasher is running as good as new.I ordered these parts on Friday morning. They were on my door step Monday morning, I highly recommend ordering from this site.
Fully open dishwasher door to horizontal position, remove lower dishwasher rack and relocate to another temp location, grab old lower door seal from right or left corner and pull completely out of door, lay the old bottom seal aside facing the same direction as once installed (seal has a notched side which faces the right side of door), match direction of the new seal with the old seal (match the notched side of seal to the right side of door), gently push the seal into the door starting on the right side (notched side of seal fits tightly into a receiving area inside the door), and finally push the remaining portion of the seal into door (aligning with the right side already properly seated inside dishwasher door). Close dishwasher and run water cycle to confirm leak.
unscrewed the old upper arm spray nut off and rescrewed the new one on....very easy...then I took the old gasket out of the bottom of the door and replaced by sliding it in. very simple....less then 15 minutes for both and have solved my issues.
Pulled out old gasket from bottom of door with needle nosed pliers and then put in new one in.
Much easier than I expected. The bottom of the door gasket simply pulled out and the new one slid back into the same spot without any issues. That gasket did not solve the problem. The unit continued to leak. We waited for the back ordered door gasket approximately 2 week to come in. Once it came in the process took about 10 minutes. The old gasket easily pulled out of it's groove around the door. That gasket was dried out and worn in several places. We fitted the new gasket in the groove, trimmed off the excess, closed the door and ran the dishwasher and had no leaks. The two gaskets definitely did the trick. This is an easy DIY for anyone and the parts were priced right!!
DO NOT BE TEMPTED TO REMOVE THE INNER DOOR SCREWS!!!!! I was and added about 10 minutes to a repair that should take less than 5. The lower door gasket just pulls out the bottom of the door. No tools required, just pull it out. The new one just pushes in, no click or anything, just make sure it bottoms into the groove.
Removed screws and put new bottom gasket in old one just fell out.
took the door off after several failed attempts, which is easy to do - 2 scews. Then it was easier to find the channel the gasket fits into.For all Frigidaire diswasher owners, after taking the door off, I realized it was the seal around the soap dispenser that was leaking, due to stripped screws, not the gasket. I rigged it with silicone caulk, but may have to replace that - looks easy, .
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.