http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/UTGT4VNQ.gif
See part 38 in the diagram

BRNG&SEAL

PartSelect Number PS9493640

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Unusual Noise.
  • Will not tumble.
  • Compare At

    $63.73
  • You Save

    $10.62
  • Your Price

    $53.11
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.9 / 5.0, 10 reviews What's this?
1-10 of 10
 

26 of 34 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerRobert from Parker CO

The rear drum seal was worn and causing streaks on clothes

I new that the drum would need to be removed to perform the seal replacements but it didn't look that difficult. Sure enough, it was a piece of cake. The whole process of installation took less than one hour to complete. The saving to repair vs. replacement of the dryer amounted to the equivilant of 4 - 5 rounds of golf. Yes I would do it again!

Help other customers find the most helpful instructions.

Were these instructions helpful?

21 of 22 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsNutdriver, Screw drivers

CustomerStephen from Springfield MA

Dryer making loud squealing noise when running

The (front) bearing and seal are not metal parts but a fabric and and mesh like material. It is somewhat like a fabric belt made to hold up a pair of trousers. The belt sits in a channel that goes around the door on the inside of the front panel. To get to the combination bearing/seal you remove two screws that are located under the cover of the lint trap. These have to be removed to lift the top. Then using a putty knife or screw driver you must pop the top (which snaps down on plastic clips) at the front corners. The top lifts up and folds back on hinges. The front is attached to the sides by one screw on each side near the top. A nut driver will remove then easily. Once the 2 screws are removed lift the front panel about 2 inches to disengage the front panel from the clips that hold the front attached to the sides near the bottom. When you remove the front panel the dryer drum will literally fall out so you want to get hold of it before pulling the front panel away so it isn't damaged and and doesn't damage the gas burner assembly which is under the drum to the left side. The drum is very light. I supported it with an empty shoe box while the front was off.
Once the front is off you'll see the bearing/seal on the inside of the front panel and it will be obvious how to remove the old one and place the new one. There are three pegs on the front panel that receive the three holes in the fabric bearing/seal. The seal will stay in place while you remove the shoe box and put the front cover back on. The drum fits over the seal like a lid on a jar and just slides on the fabric when the drum rotates. Low tech but the drums slides easily on the bearing material and seems to last a long time.

I also did the rear dryer seal. This is similar to the front. To do this you follow the procedure above but to get to the real seal you will have to remove the drum. It will fall out on its own if the front panel is removed. The drive belt goes around the drum. It is about 3/8th of and wide and just wraps around the drum without any teeth or channels or anything. Let the belt fall to the bottom as you lift the drum forward and out of the cabinet. The drum is light. Just put it on the floor and strip off the old rear seal which is glued on. It too is fabric. Clean up the drum a little and fit the new seal on the drum. Once the seal is on the drum you can lift the edge of the fabric seal and glue the fabric flange to the drum. This becomes pretty obvious once you have the seal on the drum. If you put the glue on the drum first you will make a mess. Put the seal on properly and the lift the edge to apply the adhesive all the way around. The adhesive sets enough in a hour or so. Put the drum back in and replace the front panel. Don't forget the drive belt. It goes around the drive motor that is located on the bottom of the dryer on the right, around or over an idler pulley (my older model does not have a idler wheel but rather a bracket with a "slide" that the belt runs over that keeps sufficient tension on the belt to drive the drum. If your belt falls off the motor and the idler pulley falls out it may be confusing how the belt goes in. My idler bracket is held in slots on the bottom of the cabinet merely by the tension of the belt - no screws or anything. I suggest that you put the belt around the drum first, then the drive motor. You will have slack in the belt and it becomes a little more obvious how the idler pulley (which is mounted on spring steel) goes in and takes up that slack and keeps modest tension on the belt. The rubber side of the belt goes against the drum, the leathery side is the outside.

Help other customers find the most helpful instructions.

Were these instructions helpful?

15 of 23 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsNutdriver, Screw drivers

CustomerChris from Worcester MA

Motor tried, but could not turn drum

First, I unplugged it and pulled it away from the wall. Then I pryed the front of the top up. It is scary to apply that much force, but the clips did not break. It opens like a car hood. Then I removed the two sheet metal screws that hold the front to the sides. Don't forget to unplug and unclip the door switch wires. Then I lifted the front off the bottom clips. Be sure to hold the drum up when you do this. Three hands will make it easier. Then remove the drum and belt. The belt tensioner will fall off, but that is ok.

I thought the problem would turn out to be the motor, but instead it was the front seal for the drum. It is felt and had broken. It folded under itself and was jamming the drum to the point that the motor couldn't turn it.

I replaced the felt seal, which attaches to the front cover with three clips and also replaced the plastic guides, which clip to the drum. Both were easy to do. I had replaced the rear drum seal a few years ago and so it was ok, otherwise I would recommend doing that too.

While I had it apart, I opened up the back and cleaned out all the lint in the fan housing. I had replaced the heater element, thermal switch and fuse a few years ago, so they were fine.

I also replaced the mosture sensor, just because it only cost $11. I bought a new lint filter, because it had holes in it after 20 years. I replaced the belt, because it was only $10. I replaced the lint filter cover and front door handle, because they had yellowed. I will warn you about the front door handle. It was a bear. I finally had to take the door apart to get the little plastic clip to seat correctly.

Then I put it all back together, which again is easier with 3 hands. Holding up the drum and putting the front cover on the lower clips can be a bit tricky alone. Also, be sure to rotate the drum to make sure the rear seal is not folded under and the front seal is seated correclty.

I fired it up and it ran great, except for the constant whistling. I had wondered what the little clear plastic box in the back did. Turns out it is the lint filter is full whistle warning thing. I took the back off again and found a wire was resting on the flapper door of the box and holding it in the wrong postion. By the way, it is a really irritating sound after the first few minutes. I moved the wire and it works great.

I worked slowly and it went well and was not hard.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsNutdriver, Screw drivers

CustomerNeil from Southgate MI

Front seal was ripped.

Step one: UNPLUG THE 220V LINE!
Removed the 2 screws on top under the lint door then flipped up the top. Next I unclipped the wire harness at the front and disconnected the 2 wires to the door switch and flipped the harness out of the way. Then I popped off the kick panel. Next, I removed the (4) 9mm screws holding the front panel on. The 2 lower screws only need to be loosened and the panel lifted off. Note the location of the door springs at the bottom. These springs can be reinstalled easily through the kick panel after you reinstall the front panel.
Next I removed the remnants of the old seal from the front panel but left the 3 plastic clips in place. The seal wraps around the perimeter of the panel and is held in place by the lip of the opening. The extra flap is then folded back so that the folded edge is toward the dryer drum and away from the front of the panel. The sketch in the instructions is not helpful!
Next, reinstall the front panel. As you set it onto the lower screws, you may need to lift the drum slightly to fit the panel into the drum opening. Tighten the 4 screws then reattach the 2 door springs. Test the operation by turning the drum counterclockwise by hand. Check to make sure the rear seal has not been displaced or damaged. That seal is actually glued into place. If it turns smoothly, snap the kick panel back on and reinstall the wire harness. Flip down the top and reinstall the 2 screws at the lint tray on top. Plug it in and give it a spin!.
Note, While you have it open, you'll want to use your shop vac and clean all the lint and pocket change out of the machine. You might as well take off the back panel and clean up in there and in the vent pipe too.
I didn't know if I needed a new belt but ordered one anyway. The old one turned out to be pretty well shot. After I had the front panel removed, replacing the belt is very simple. There is an idler pulley underneath that is under tension. Just push on the idler until the belt is loose. Switch the new one into place and you are done.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 3 people found this instruction helpful

Parts Used

  • BRNG&SEAL

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerStephen from Charlotte NC

Loud screeching noise when dryer running

First, removed the bottom cover below the dryer door. This is just held on with two clips that can be pushed in with a flat screw driver. Then remove the springs that go from the bottom of the dryer to the inside of the dryer door. We had to remove the entire front of the dryer, so the easiest way we found was to loosen the two screws on the bottom of the front panel, but not remove them. Then pop up the top of the dryer. To lift the top, first remove the two screws under the little door where the lint trap goes. The top is hinged in the back, and it snaps down onto two clips that can easily be popped up with a flat screw driver) With the top opened, there are two screws accessible. When the front of the dryer is removed, there will be nothing to support the drum, so what we found was that if you rotate the drum, you'll find a point where there's a hole in the top of the drum. If you take the springs that you removed from the bottom of the door you can hook them into this hole, and hook the other end into a hole in the back wall of the dryer just behind the drum. The springs are the perfect size for this, and it keeps the drum from falling when you remove the front panel. then just disconnect the three wires going to the switch inside the front panel, and remove the two screws from the top of the front panel. It should then lift right off. The bearing can just be pulled away and the new one installed. Put everything together again in reverse order.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 3 people found this instruction helpful

Parts Used

Level of DifficultyDifficult

Time to do repair:1- 2 hours

ToolsNutdriver, Screw drivers

CustomerPatrick from Niskayuna NY

Brown "dust" marks appeared on the clothing after drying

First, I slid the top forward to release it and then pivoted it about the clips along the back edge. Second, I removed the open/closed door sensor. Third, I removed two screw on the inside of the front panel and slide the front panel up to release it from the clips near the bottom edge of the panel. Fourth, I removed the dryer drum that fell out as soon as the front panel was removed.

With the drum on the floor (carpeted), I installed the front seal and the back seal after removing the old seals. I then applied the glue supplied with the back seal to the back seal. Next, with my spouse's help, I placed the drum into the dryer frame while positioning the seals, the drum driving belt, and the front panel. This step was the most 'interesting' of the whole repair. I replaced the two screws on the inside of the front panel. I spun the drum to ensure that the seals were in the correct position.

Finally, I replaced the door sensor and dropped the top into place.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

Customercarl from westbrook CT

Drum stopped

10 min. job, easy to do / two screws top and two inside front / remove old parts install new.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerJohn from Semmes AL

Brown lines on clean clothes coming out of dryer

Removed the top and front panel, removed the dryer drum. Removed the worn out rear drum seal. I scraped and sanded the old glue residue from the rear of the drum. I used "0000" steel wool to clean the "brown seal residue" from the rear panel where the new seal on the drum would rub/seal against the rear panel. I used spring clamps to hold the seal in place prior to appling the glue. The glue was applied to the drum/seal and allowed to dry 30-45 min. I replaced the front drum seal (some of the other discussions in your forum had good hints on replacing this seal, better than the printed instructions), also replaced the belt and applied a light amout of lubrication (3 in 1 oil) to the idler pulley and the drum rollers. The dryer runs smoothly and quietly and most importantly no more brown streaks on clean clothes.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:More than 2 hours

ToolsNutdriver, Screw drivers, Socket set, Wrench set

CustomerWalter from Memphis TN

Black streaking on white clothing

the repair was straight forward. I am a machine shop owner so I have a little knowledge about mechanics.the repair took 2 and 1/2 hours due to cleaning lint from everything that I could reach and removing all of the excellent factory adhesive. If someone could do this repair in less than one hour properly. .

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 3 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerPeter from Seabrook TX

Drum seals worn

Unplugged dryer. Removed lint trap and the two screws under lint trap. Popped top up. Removed two wires to door switch. Removed two nuts holding front on and removed front of dryer. Pulled drum out and placed on ground.

Pulled old rear seal off and sanded off old glue. Placed most of new seal onto rear lip of drum and glued. Held it in place with clothes pins. When glue dried, pulled remaining seal into place and glued. While it dried, I replaced the front bearing.

Reinstalled drum into dryer with new belt. Used screw driver to set rear seal over buldge in rear of dryer. Replaced front of dryer. Ran dryer with top up to assure seal and belt were set.

Reclipped top, replaced screws and lint trap.

Directions included were very clear and.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-10 of 10