| |
4 of 9 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:30 - 60 mins
ToolsScrew drivers
CustomerJacob from Miami FL
Ice door holder brocken
To replace front cover and ice door kit I had to check the new cover how it is cliped on the bottom to remove the old cover, but after that it was not very difficult.
|
1 of 3 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:30 - 60 mins
ToolsNutdriver, Pliers, Screw drivers
CustomerFrank from Sandy UT
Ice door would not close
I removed the Ice door front cover on freezer door. Found door pivot was broken. I installed door pivot bracket, and dashpot in kit. I used most of the kit to repair it. The door now works like new. Thanks for the right parts Frank
|
2 of 6 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerJerry from Hephzibah GA
Will not make ice
turned off the machine. removed the ice maker door. removed the wiring harness cover. press on locking clips, removed ice maker. disconnect wiring harness. removed three screws from cover and installed on new ice maker. installed in reverse order of removable.
|
1 of 3 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:30 - 60 mins
ToolsScrew drivers
CustomerStacey from Kingman KS
The ice door chute was not closing tightly, so there was a freeze/thaw problem which was slugging up the ice auger.
I killed the power to the fridge on my breaker box before I started the repair job. I popped the dispenser panel off by slipping two screwdrivers(one in each slot on the bottom of the panel). Then I removed two screws on the wire panel beneath in order to get to the ice door chute. (Take a mental note of how all the parts are positioned that you must replace.) I had to remove the pin in the ice door lever, then I replaced the spring and the ice door(flapper) with the new ice door support (timed release closure). The new ice door support doesn't require the white shroud that existed on the previous part. The most difficult part of this repair was having the patience to deal with the wire panel dangling in the way, and trying to contort myself in awkward positions to be able to see what I was doing. My hands are large, so it was difficult to maneuver them in order to make everything fit back together. If you have someone to hold the panel up out of the way while you are working, it would be much easier. If you have a short mechanic's creeper chair, it would be helpful!
|
5 of 15 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:More than 2 hours
ToolsScrew drivers
CustomerJohn from Palmdale CA
Ice flap in door was not closing causing excess frost
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:30 - 60 mins
ToolsPliers, Screw drivers
CustomerCarl from Mt Juliet TN
Plastic door bracket for icemaker chute broken
Googled with question about how to get to the repair as there were no screws on the faceplate. Found I had to lift the faceplate at the bottom and pry out. Was kind of hard to get the long spindle back through the ears of the bracket holder along with getting the spring of the door lined up for the spindle to pass through to the other side. Finally got it right and then just put it all back together. Frustrating at first but I had to get it done as my wife was tired of having to take large clumps of ice out of the ice tray..three years wait for the repair. That door being open let warm air in and let the ice melt just enough to stick together in a clump. All is well now. Longer you wait the more appreciative she is however. ha
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:1- 2 hours
ToolsPliers, Screw drivers
CustomerBetty J from Amherst VA
Ice cube door would not close pr0perly
Because of the design change of the door hinge it was more difficult to slide the pin into the door and spring. I used an allen wrench to hold it in place on the left side so I could slide the pin in the right hole. Then removed the allen wrench so I could slide the pin all the way. I was very impressed with the time that it took to get the kit. I ordered it about 1:30PM and the following day I had the kit delivered by 6PM. FANTASTIC SERVICE!
|
2 of 8 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:30 - 60 mins
ToolsScrew drivers
CustomerMichelle from Springfield IL
Ice/water dispenser broke
This went together like a puzzle. With the help of the diagram it was fairly easy to do. Most importantly I ordered the part in the morning and it was there the next day without even paying overnight delivery...very impressed!
|
2 of 9 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:30 - 60 mins
ToolsNutdriver
CustomerJudy from BELMONT NH
Flapper on the ice maker door came off
I called Alpine Appliance Repair out of Laconia NH. Barry came over and handled the rest.
|
1 of 6 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:30 - 60 mins
ToolsNutdriver, Pliers, Screw drivers
CustomerBill from Mesquite TX
Ice dispenser was freezing up due to the broken door
The repair went pretty easy. You must remove the cover and lift up the electronics to gain access. The instructions were a little vague since the new door/chute didn't have the electric heater wire. I eventually realized that it wasn't needed and replaced the door without further incident.
With a new valve in the back, I now have water and ice at the door after a couple year hiatus!
Thanks.
|
6 of 25 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:1- 2 hours
ToolsNutdriver, Screw drivers
CustomerHoyt A Sulvin Sr from Irwindale CA
Ice make would not dispense out the front door.
Unpluged the unit and removed the front trim ring.
removed the old parts and installed the new parts.
in reverse order. it took about 12 hour but the dispenser to work but seems to work fine now.
|