897030-1-S-Whirlpool-8182119           -Bellow
897030-1-S-Whirlpool-8182119           -Bellow 897030-2-S-Whirlpool-8182119           -Bellow http://www.partselect.com/Schematics/Maytag/EJVNLADB.gif

Bellow

PartSelect Number PS897030

This part is also called the Door Boot Seal. It's the main seal between the front bulkhead and the outer tub. Clamps are not included. Must order clamps separately, if needed.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Leaking.
  • Compare At

    $133.00
  • You Save

    $22.17
  • Your Price

    $110.83
In Stock
Order within the next 11 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Bellow to Outer Tub Clamp

Part Number 897088

Used to help hold your bellow in place on your washer.

Order within the next 11 hrs and your part ships today!
$20.99
In Stock

Bellow Clamp

Part Number 897089

This is used to help hold the bellow in place.

$16.09
On Order

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.1 / 5.0, 18 reviews What's this?
 

13 of 16 people found this instruction helpful

Parts Used:
  • Bellow
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Jerome from Albquerque, NM

Kenmore bellow between door and washer tub ripped

I followed the repair blog by the poster most liked...

Help other customers find the most helpful instructions.

Were these instructions helpful?

11 of 16 people found this instruction helpful

Parts Used:
  • Bellow
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Tom from Spirit Lake, IA

Door leaked water

First step was to remove old bellow. I opened the door there is a small wire with a spring attach that holds the outside of the bellow to thw washer. Then removed it from the water inlet, then took a short straight scewdriver to remove the gaint hose clamp holding it to the drum. Installed the new part. When putting hose clamp back on I removed the top of the washer by removing the three screws in the back then I flipped the hose clamp so I could use a long screwdiver from the top side.This will give you alot more room. Hope this helps

Help other customers find the most helpful instructions.

Were these instructions helpful?

9 of 15 people found this instruction helpful

Parts Used:
  • Bellow
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Screw drivers
Customer: Ramon from Houston, TX

Front seal leaked

It was so easy my wife replaced the part.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 7 people found this instruction helpful

Parts Used:
  • Bellow
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers
Customer: RICHARD from Portland, OR

Old bellow pulled loose and torn

Was able to remove old bellow without dis-assembly. Replacement required removing the front of the machine for access. Once the front was off, the bellow was simple to replace. Biggest difficulty is getting the top mark on the bellow lined up. It has a tendency to slip out of position while you are working the back of the bellow over the retaining lip and it is not possible to rotate the bellow after it is installed. Fortunately, the tube from the detergent tray can be rotated slightly to allow for a small amount of error. Replacing the front retaining wire and spring required three hands at one point, but was otherwise not a problem. Fortunately removal and replacement of the front of the machine is pretty straight forward. I needed to disconnect wires to set the front out of the way, but it is impossible to plug them back in incorrectly.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 8 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Socket set
Customer: Richard from Bayport, NY

Blower worked, but no heat

i followed your instuctions for the gas dryer with the ohm meter which i had, and found the part that had 0 ohms. but i did clean all the lint out first that took more time. i was glad you had the diagram to show the parts and numbers. thank you, rich

Help other customers find the most helpful instructions.

Were these instructions helpful?