| |
20 of 21 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsWrench set
CustomerAnthonie from Beale AFB CA
Old hose had a leak
First I removed the screws that held the hose drain hose clip in place. Removed the damaged hose. Placed the new drain hose clip at the end of the new drain hose. Re-inserted back in hole, pushed in hose to necessary depth then tighted screws, Very easy and painless.
|
8 of 9 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerAndres from Stamford CT
Changed drain hose on ge washing machine
I attached the Drain Hose Clip to the Drain Hose Extension and then pushed the drain hose all the way into the drain hole in the back of the machine. I then screwed the clip to the machine. Done. Very painless. Fast delivery... ordered it on Monday, arrived on Tuesday.
|
7 of 7 people found this instruction helpful
Parts Used
-
- Drain Hose Extension - 4 1/2' Long
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsSocket set
CustomerDaniel from Oxford GA
Purchased used washin machine w/o drain hose
After realizing I had purchased a used washing machine without a drain hose I thought I would never find one, but then I found partselect.com. After easily locating the part on the web site from the detailed diagrams and model number I then ordered it. Receiving the part quickly I used a socket to remove the plastic connector that prevents the hose from disconnecting once the washer is turned on. I fed the hose through the plastic connector and into the drain hole without any issues. I then used my one small socket to secruely fasten it back together. There was no additional tools or items needed to successfully attach the washer drain hose.
|
8 of 10 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerDARYLD from SCHOFIELD WI
Hose and clip were broken in moving
The parts were here in 3 days and the repair went very quickly .Quality item would do business again.
|
5 of 7 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsNutdriver, Pliers, Screw drivers
CustomerPaul from Perrysburg OH
Overflowing washer
Unplugged the washer and unscrewed the hot and cold filler hoses from the back of the machine. Removed the 6 screws holding the top together. Unscrewed the 2 water valve mounting screws. Pulled off the electrical wires from the leads. Unclipped the water feed hose clip. Reattached everything to the new water valve in reverse order. Put the screws holding the top panel in place back in.
For good measure, I also replaced the drain hose since I had noticed a little leakage there. Two screws and a little twisting and pushing was all that took.
Then I hooked everything back up and it worked like a charm. Finally, I went out to dinner with my wife on the money I saved!
|
4 of 5 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers, Wrench(Adjustable)
CustomerJennifer from Concord CA
The hose extension had a tear
First I removed the screws that held the drain hose clip to the washer. Then I pulled the hose, along with the clip, completely out of the washer. I then took the old hose out of the washer clip and put the new hose in the new clip; I pushed the hose into the washing maching and tightened the hose clip to the maching with the existing screws. Seriously easy, took less than 15 minutes. And I have virtually no handyman skills at all!
|
3 of 3 people found this instruction helpful
Parts Used
-
- Drain Hose Extension - 4 1/2' Long
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsSocket set
Customerkartik from radnor PA
Drain hose had a hole in it
used a socket to unscrew the clip. pulled out the old hose, slid the new hose into the clip and screwed the clip back on. all fixes should be this easy.
|
3 of 4 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsNutdriver, Pliers
CustomerNolan from Fort Polk LA
Water was leaking from the tub to the floor.
First I removed the two clamps that hold the inlet drain hose onto the pump. **There may still be water in the hose** This was pretty easy, but a set of vice grips would have been nice. The space is not too cramped, but required a little bit of wiggling. Putting it on was a little bit harder, just because I did not want to tear the hose on the tub or pump inlet. Make sure both are fully seated or else it could still leak. The drain hose and the clip are pretty self explanatory. I tried to buy a generic drain hose at a big box lumber yard, but I could never make it fit right.
Hope this helps.
|
2 of 2 people found this instruction helpful
Parts Used
-
- Drain Hose Extension - 4 1/2' Long
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerMohammed from Berkeley CA
Drain hose was leaking
Surprisingly easy. I took the screws off, then pulled off the drain hose. I then inserted the new hose, and put back the screws. Amazing quick!
|
2 of 2 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerHenry from Merced CA
Drain hose replacement
Put the drain hose clip on (it will take squeezing but the hose will pass through). There will be a groove that whose width spacing is similar to the clip. Once that's on, insert hose and screw in the clip.
|
2 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerCraig from Peabody MA
Leaking hose
Unscrew the 2 screws holding the drain hose clip to the machine - use bucket to get an excess water - remove bad drain line - I installed a new drain hose clip as well - make sure you put the clip on at the same position as the previous hose - push house firmly into opening and screw into machine - pretty easy repair - and I'm a novice
|
2 of 2 people found this instruction helpful
Parts Used
-
- Drain Hose Extension - 4 1/2' Long
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerTruett from Kennesaw GA
Hose had a small pin hole. Leaked.
With screwdriver, I removed screws holding old hose in place. Attached new hose and screwed into place.
|
2 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsSocket set
CustomerJames from Kennard TX
Drain hose leaked
i removed 2 screws , pulled old hose out and put new one in.5 minutes,done.
|
1 of 1 people found this instruction helpful
Parts Used
-
- Drain Hose Extension - 4 1/2' Long
Level of DifficultyA Bit Difficult
Time to do repair:30 - 60 mins
ToolsNutdriver
CustomerCharles Wayne from Forest Hill WV
Hose would not seal at rear of washer.
The hose has a tapered end that fits in a tapered hole in the back of the washing machine.When insalled the first time,the joint leaked badly.My solution was to coat the hose end and the interior of the hole in the back of the washing machine with silicon sealant;let it set up for a few minutes and install the new hose.This solved the leak and the hose seems to be working fine now.
|
1 of 1 people found this instruction helpful
Parts Used
-
- Drain Hose Extension - 4 1/2' Long
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
Customerpeggy from sulligent AL
Busted drain hose
It was really easy to replace i removed the old one & sliped on the new one.
|