889134-1-S-Whirlpool-9706648           -Speed Control Switch Assembly
889134-1-S-Whirlpool-9706648           -Speed Control Switch Assembly 889134-2-S-Whirlpool-9706648           -Speed Control Switch Assembly

Speed Control Switch Assembly

PartSelect Number PS889134

This assembly includes the black knob. Used with Stand Mixers.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Touchpad does not respond.
  • Compare At

    $67.93
  • You Save

    $11.32
  • Your Price

    $56.61
In Stock
Order within the next 8 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.5 / 5.0, 8 reviews What's this?
1-8 of 8
 

24 of 27 people found this instruction helpful

Parts Used

  • Speed Control Switch Assembly

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerJames from Villa Rica GA

Mixer speed was uncontrollable

Removed screw from back of mixer cover band and then removed the 4 side screws, lifted top off of mixer and removed screws from circuit board control switch, removing wires one at a time so as to install correctly. replaced screws in circuit board/control. Restored top of mixer replaced screws and the put cover band back on mixer.walla done

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 8 people found this instruction helpful

Parts Used

  • Speed Control Switch Assembly

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

Customerjerry from farmland IN

When turned on mixer went full speed for 10 secs. Then shut off. When turned off then this repeated. Trouble guide indicates defective speed control.

per e.g. and put cover on and secured screws. Pluged in unit turned it on and it worked for 25 secs then went full speed and shut down.. repeat this several times got same results. Put old unit back in and it worked for 2 days then same results. I now suspect coil on shaft is defective. I'll order that and see. Unless some one knows of another problem.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 8 people found this instruction helpful

Parts Used

  • Speed Control Switch Assembly

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerThomas from Christiana TN

Speed surged after mixer warmed up

Took off cover, marked leads, unscrewed two screws and replaced circuit board (speed swith unit). This one was really easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 7 people found this instruction helpful

Parts Used

  • Speed Control Switch Assembly

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerChristine from Maple Valley WA

Speed control failed to work properly

Unscrewed stainless steel Kitchenaid band, removed screws holding down the main housing to get to the speed control panel. Removed two screws from to release the speed control panel, replaced the panel with new part, and replaced all the screws to the main housing, and stainless steel band and it worked like new. So easy, and it only took about 15 minutes to repair.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 5 people found this instruction helpful

Parts Used

  • Speed Control Switch Assembly

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerBrandy from Thorp WI

Speed control went. The beater would fly in any setting

I carefully removed the cover of my mixer. I first made sure that all of my part numbers corresponded, then I labeled the 5 wires that needed to be disconnected. I then disconnected the wires, removed the two screws holding the part in place, switched out the old for new, reconnected all of my wires. Mades sure everything looked tight, and put my cover back on. Works like a charm. I cried because what I really thought was going to be a $200+ fix, ended up costing me less than $50! And it was so easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 5 people found this instruction helpful

Parts Used

  • Speed Control Switch Assembly

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerEleanor from Perry NY

Thank you,

my hasband did the work and i an so happy it is working good for me now,

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 3 people found this instruction helpful

Parts Used

  • Speed Control Switch Assembly

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsPliers, Screw drivers

CustomerFred from Coeur d'alene ID

Motor would surge after a few moments of running then die.

so easy to remove the switch. I first marked the wires, 1-2-3-4 and then removed them from the old switch. removed the old switch and replaced with the new one and plugged in the wires as per markings. tried it out before replacing the top and it works perfectly. no longer timid about effecting repairs on my own. the diagrams on the website were a great help. this is a great company to do business with. part was here in 3 days.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 5 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerRafael from Brooklyn NY

The drive gear keeps popping off

I ordered the retaining rings from PartSelect and by mistake I did enter the wrong address for the delivery. I got a notification that the parts were delivered. When I called PartsSelect they toll me not to worry, they send me a new shipment to the correct address immediately. I have to add the retaining clips used by PartsSelect or KitchenAid are substandard, they are not hardened enough to hold the load of the motor and bread dough. These clips keep on popping off and losing tension.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-8 of 8