http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/54116.gif
See part 10 in the diagram

BURNR-HEAD

PartSelect Number PS8768535

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Gas igniter glows but will not light.
  • Will not start.
  • Cooktop element not heating.
  • Compare At

    $40.07
  • You Save

    $6.68
  • Your Price

    $33.39
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.9 / 5.0, 4 reviews What's this?
1-4 of 4
 

6 of 7 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerJAN from HOFFMAN ESTATES IL

Stove's plastic end cap was cracked, burner head worn out.

Investigated the stove top and found worn part under stove top burner. Looked up defective/worn out part on line at Parts Select web site. Ordered on line and in a few days had a box sent with new part and replaced it. The repair time was 25 minutes or so. Part began to work properly. Plastic end cap was also swapped for a new one.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 6 people found this instruction helpful

Parts Used

  • BURNR-HEAD

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerDerek from Seattle WA

One of the burners would not autolight, had to be lit with match

This was VERY easy and I've never worked on this type of appliance before.

First, take off the grate, thermal plate, etc that are resting on top of the stove (this is all the stuff you take off to clean the stovetop).

Then, carefully unscrew the two screws holding the burner to the gas pipe. Grab the screws and set them aside so they don't fall back into the stove, then pick the burner up off the stove.

once you have the burner a few inches above the stove surface, wiggle off the single wire by grabbing it on the metal part (not by the wire) and gently wiggling it off.

Grab new burner, push on wire and sit it on stove, use a finger in the gas pipe to align it and put the two screws in. you're done.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 8 people found this instruction helpful

Parts Used

Level of DifficultyDifficult

Time to do repair:More than 2 hours

ToolsScrew drivers

CustomerRosemarie from Huntington NY

Ignitor couldn't be removed because the screws were ruined.

This is the second time I have had to call a repair person to GE the old screws off. It isn't the fault of the part. Better original screws would have helped. It was very frustrating an expensive. I would say check the screws before you order the part.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 5 people found this instruction helpful

Parts Used

  • BURNR-HEAD

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerJohn from Sonora CA

Burner would not ignite even with gas flow spark and clicking.

Removed two screws and disconnected the ignition wire. Then connected ignition wire to new burner and installed two screws

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-4 of 4