http://www.partselect.com/Schematics/GE/GE_Thumb/00110803i04.gif
See part 655 in the diagram

PUMP

PartSelect Number PS8768445

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Will not drain.
  • Leaking water.
  • Pumps but will not spin.
  • Unusual Noise.
  • Compare At

    $64.07
  • You Save

    $10.68
  • Your Price

    $53.39
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.9 / 5.0, 53 reviews What's this?
46-53 of 53
 

0 of 1 people found this instruction helpful

Parts Used

  • PUMP

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsPliers, Socket set

Customermichele from Deerfield Beach FL

Machine would not drain

I looked up what others said about the same problem. Took their advice, ordered the pump and it was installed in less than 30 minutes. This is the third time that we have ordered parts and have had excellent service. We usually get the parts the next day or at most two days. Instructions to repair are exactly like the customers say on the website. I tell all my friends and relatives about your site.Thanks PartSelect!

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • PUMP

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerTammy from Belle WV

Water level would'nt empty to allow spin cycle

with a blade screw driver, I released the clips holding the front cover (from the top cover) tip the panel foward and lift off of pins on bottom. I put some towels in the bottom to absorb any water left after removing all I could with a cup. Then I released both clamps with pliers, pushing them back on hoses. Using a 10 mm nut driver, I removed the pump. I then mounted the new pump, pushed hoses on and slid clamps in position with pliers(while squeezing pliers) Voila, it works like it's new. Thank you Parts Select

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • PUMP

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Pliers

CustomerDennis from Douglaston NY

Machine would not pump out completely leaving very wet, soapy clothes.

Pulled off front cover of machine. Unplugged unit. Used a channel lock (water pump pliers) to squeeze the hose clamp on the suction hose. Pulled hose off of pump suction. Did same for discharge hose. Some standing water came out onto floor of unit. Unscrewed 2 screws from base using nut driver. Pulled the 2 wires off of the stabs of pump. Re-installed new pump in reverse order. Unit back on line in 15 minutes, and works fine.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • PUMP

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers

Customermike from Manlius IL

The machine was pouring out water on the floor

i took out the two screws that mount the pump to the base of the washer, then i took a pair of channel locks to disconnect the clamps on the drain lines. thats it. i put the new one in and it works great!

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • PUMP

Level of DifficultyEasy

Time to do repair:More than 2 hours

ToolsNutdriver, Pliers

CustomerHarold from Mocksville NC

Water was leaking underneath

remove screws from bottom of washer to remove the bottom of the washer so you can access the pump and motor assy. and remove two hose clamps.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

  • PUMP

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers, Socket set

CustomerPaul from Medina NY

Pump was plugged

First i removed the bottom of washer and removed clamps from two hoses connected to the pump , removed 2 pump bolts along with wire connector. Then reinstalled new pump, hoses and wiring and that was it. Very easy !

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

  • PUMP

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers, Socket set

CustomerJeffery W. from Bismarck ND

Pump leaking

First I uplugged the machine and removed the front cover of the machine by prying outward at the top corners with a screwdriver. Then I removed the two bolts from the mounting bracket and unplugged the electrical wires. Then using a pliers I squeazed the hosed clamps and slid them back on the hoses and pulled the hoses off the pump.

To install the new pump, simply reverse the order and check for leaks. The whole process took about 20 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 10 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsPliers, Socket set

CustomerTerry W. from Mauldin SC

The pump motor stop working and the tub cover was cracked catching an picking clothes

I sold the washer to a friend of mine and gave him the parts as soon as I receved them. He passed on to me that everything was easy very simple 30 - 60 min he was done with both repairs. Everything worked great with no assembly issues. Also I recieved the parts ontime and faster then I expected. Thanks again. Terry F.

Help other customers find the most helpful instructions.

Were these instructions helpful?

46-53 of 53