871336-1-S-Whirlpool-285938            -Timer
871336-1-S-Whirlpool-285938            -Timer 871336-2-S-Whirlpool-285938            -Timer 871336-3-S-Whirlpool-285938            -Timer

Timer

PartSelect Number PS871336

The timer controls most of the operations of the washer: water level, tub filling and emptying, length of cycles, and cycle setting sequences. Includes mounting screws.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Timer will not advance.
  • Will not drain.
  • Compare At

    $158.48
  • You Save

    $26.41
  • Your Price

    $132.07
In Stock
Order within the next 7 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.4 / 5.0, 3 reviews What's this?
1-3 of 3
 

23 of 25 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerJoe from Covington GA

Washer would not wash on "normal" cycle. Had to play with the knob to get it to run at all. Washer would not drain properly either.

I unplugged the washer from the electrical outlet.

I then removed the drain hose from the wall drain to allow me to turn the washer to gain access to the the back panel.

From the front, I then removed the plastic timer knob from the timer by unscrewing it. Then I pulled the plastic plate with the arrow on it to remove it. This exposed the screws that attached the timer to the control panel. I left them attached.

I then removed the two screws on the bottom of the front of the control panel (on each end) that attach the control panel to the washer.

I then went to the rear of the washer and removed the two screws on the top of the rear of the control panel.

I went back to the front and pulled the control panel forward and up to release it from the washer.

I then removed the two screws (that were under the plastic plate) that attached the timer to the panel and removed the timer from the panel.

Then I unplugged the wiring harness from the timer and removed the timer completely.

From there I reversed the procedure to install the new timer and knob.

Help other customers find the most helpful instructions.

Were these instructions helpful?

10 of 18 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerAlan from Madison WI

The machine stops after filling water

First I removed the two scews that hold the front panel in place. I then turned the knot counterclockwised to loosen it and I used the flat tip scew driver to pry the clear plastic ring that was underneath the knot. I then removed two screws that hold the timer to the panel. I then flip the panel to the other side to disconnect the connector to the timer. I then pluged in the new timer and reversed the sequence.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 7 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

Customerscott from milford PA

Timer knob would not stay out , broken...!!!!

as a 35 year AUTO / TRUCK tech , it was a no brainer. saved a service call/ charge !!!!!. part was correct , NEW TIMER installed !!! , back up and running.THANKS !!! HAPPY WIFE, HAPPY LIFE....

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-3 of 3