| |
49 of 53 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerJeff from Springfield MO
Track broke that guided one of the drawers
I used the diagrams I found on line to order the part and then simply removed one track and installed the new one. Cleaned up all components and reinstalled the drawer. These tracks simply slide up and over to lock themselves into the bracket that attaches to the adjustable shelves bracket.
|
10 of 10 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerTerri from Wichita KS
Tracks for the deli drawer were broken
I removed the old tracks and installed the new ones. There were small round protrusions on the new tracks that prevented me from sliding them into the brackets in the refrigerator so, I filed them down with a fingernail file and then they slid right into place.
|
8 of 8 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:15 - 30 mins
Tools
CustomerCynthia from Tucson AZ
Replacing slide track to meat drawer shelf
The slides fit into the slots of the self metal, but couldn't be pushed forward to lock into place! At first I tried to put the slider in by hand, but it wouldn't snap in place no matter how hard I tried. A friend also tried to get the slider into the slots and push forward to lock in place in the metal part of the shelf. No go! It took a while, but I figured if I used a hammer to tap the slider into place that might work. It did. It would have been helpful to have some instructions on inserting the slider, such as "use a hammer tap the slider so it locks the slider into place". You just can't do it by hand! Other than that, it went really well and replacement then only took 1 minute. . .instead of the 30 minutes it took to try to lock the sliders.
|
6 of 7 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerRandy from Copley OH
Track that veggie drawer slided in broke
This website is fantastic! I was able to watch a video of the piece being installed. The world wide web is an amazing thing. Thanks for being there...
|
5 of 6 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsScrew drivers
Customerpaul from wrentham MA
Dishwasher arm would not turn
we removed the cracked pieces and attached the new spray arm. it took some time because the new arm looked different than the old,but we did it.... I was the one to order the parts needed i had never done this before my husband said it was broken and we needed to buy a new dishwasher ( he was less than thrilled about that) so i decided to do this myself and find the parts. my husband was very surprised that i did it.... AND SO WAS I... IF I CAN DO IT YOU CAN DO IT!
|
4 of 5 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
Customerrob from canton GA
Broken drawer slides
open door, remove food from shelf, remove drawer,remove drawer, pry up and remove slides, instalation is reverse
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerWilliam from Derwood MD
A broken slide track for one of the drawers
The part came in two days!! It had a couple of little bumps that made it impossible to slide in, so I ground them down and had the entire project finished in less than five minutes.
When I ordered, I was confused about the "Left Side or Right Side statement - thinking I needed to specify so I wrote a short email to customer support asking about it. WIthin an hour, I had a reply.
The customer service and speed of delivery were the best ever!!!
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerEdson from Browns Mills NJ
Right side track for drawer broken
After cleaning out the drawer and taking it out, I removed the shelf the bracket was connected to. The bracket slid out and the new one slid in with help from the rubber mallet. Should have checked the left side too, as it was cracked and I ended up ordering another track.
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerJohn G from Heathsville VA
Cold cut drawer slides kept breaking (3x)
I cut strips from the old slides, super glued them onto the new slides as stiffening where the old slides had broken. This was the 4th set of slides I had installed, a real Whirlpool design fault! I then sild the new pieces into the clips, and away we go!!
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerLARRY from OLIVE BRANCH MS
Weight of the produce bin with the contents inside had cracked the tracks
First I removed the tracks from each side of the metal rack. Very easy using your hands to slide the tab until the part falls away.
Next I inserted the track into the tab position and snapped it into place.
Warning, dont let your kids pull the produce bin out all the way to the end of the track as it will bend and then finally crack like mine did, but thankfully an easy fix using the PartsSelect.com web site with their easy to navigate parts illustration list and manual.
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyDifficult
Time to do repair:Less than 15 mins
Tools
CustomerSteve from Milton GA
Replaced two broken tracks
The old tracks had been falling out consistently, causing the deli tray to fall on top of the food below it (which included the eggs, though none were broken since they were in a hard plastic container).
I had some difficulty getting the new track installed, however. All the parts lined up, but I just couldn't get the tracks to slide into place. After some brute force and about 10 minutes, they were finally installed.
Best thing about it is that it doesn't appear that these tracks are coming out easily! Mission accomplished!
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:30 - 60 mins
ToolsScrew drivers
CustomerCHRIS from BAYTOWN TX
Meat drawer tracks(2) broken on ends
Ordered and received parts. Removed drawer and shelf unit. Removed the glass from top of shelf. Each track(2) slides out of slots on each of the metal shelf brackets. Slid old tracks out of each shelf bracket. Had to use small screwdriver to push down plastic tab that locks track before it would slide all the way out. Each new track had a small tab on each end, which would not let them slide into the slots on the metal shelf brackets. Used a small saw (could also use a file) to remove the 2 tabs on each track. Slid the new tracks onto metal shelf brackets, reinstalled shelf unit, glass top and drawer. Took about 40 minutes.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
Tools
CustomerJay from Minneapolis MN
Broken track
Removed broken tracks, installed new tracks. Had to file off two knobs on each track that prevented the tracks from seating properly. Installed easily and locked into place once the knobs were gone.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers
CustomerMaria from Exton PA
Broken track on lunch meat drawer
My husband was able to remove the broken tracks & replace them very quickly. Super easy repair.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
Tools
CustomerJohn from Alpharetta GA
Slide track cracked
removed the old track, replaced with new. snapped into place
|