Ice Maker Assembly - 8 Cube

PartSelect Number PS869316

This icemaker can be used with 25-27 cubic feet refrigerators that have a vertical auger dispenser located on the freezer door. Reuse bottom bracket from the original icemaker and attach to the new.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Ice maker will not make ice.
  • Ice maker won’t dispense ice.
  • Leaking water.
  • Compare At

    $137.57
  • You Save

    $22.93
  • Your Price

    $114.64
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.1 / 5.0, 83 reviews What's this?
 

0 of 1 people found this instruction helpful

Parts Used

  • Ice Maker Assembly - 8 Cube

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerSAM from NAPERVILLE IL

Ice maker quit working

Removed 3 screws from under icemaker and slid unit forward until I could disconnect plug on right side,which was the most difficult step of the process,and pulled icsmaker out.
Reversed the procedure with new unit, had a little difficulity with the rubber spout for the water fill,and in a while I had ice again.
Thanks to the info on your site I was able to verify that the valve solenoid was working properly so it saved me a step.
A word of caution-the icemaker plug has 120vac so unplug refrigerator before repair attempt.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Ice Maker Assembly - 8 Cube

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers

CustomerLarry from Louisville KY

Ice maker quit working

Easy repair overall. Removed three screws and icemaker casing, removed old icemaker and replaced with the new. Bracket was a little tough to get back in place.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Ice Maker Assembly - 8 Cube

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerDenise from Hanford CA

Broke ice maker

Fast delivery! Easy to install and works fine so far.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Ice Maker Assembly - 8 Cube

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerTERRI from SARASOTA FL

Not making ice

slide old ice maker out, unplug, plug new ice maker in, slide in place

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers, Socket set

CustomerRon from Bremerton WA

Ice maker wouldn't work.

First I removed the ice tray door by lifting and then releasing the hinge. Then I used a nutdriver and socket to remove three recessed screws that are located under the icemaker. I also removed the screw on the underside which holds a plastic flange in place covering the wiring harness. Remove the plastic flange and slide the icemaker out as far as possible, then disconnect the wiring harness from the icemaker. Slide the old unit out and discard. Reverse the procedure to install the new unit. Points of frustration: Disconnecting the wiring harness--it is in there mighty tight! Also, when sliding the new unit into place, clearing the rubber water spout without breaking something is somewahat of a challenge. The unit comes out
easier than it goes back in!

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Ice Maker Assembly - 8 Cube

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerRob from Round Rock TX

Ice maker would not produce ice

I disassembled original ice maker to find a short between the motor housing and the tray heater. Easiest to replace full assembly. Ordered new part, and after it arrived...

Removed front ice maker door and rear power wire cover. Slide out ice maker and removed the reusable parts and installed on new assembly. Installed new ice maker in reverse. Ice maker immediately filled with water but never went into harvest mode. I figured the optics board was bad, but it wasn't. I removed the transmitter and receiver, and let them warm to room temperature and reinstalled after cleaning optics with cotton swab. The ice maker started working like a charm.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Ice Maker Assembly - 8 Cube

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsSocket set

Customerwilliam from Chesapeake AL

My ice maker quit making ice

I unbolted the old ice maker, pulled it out, unplugged it and then I put in the new one...it was exactly the same. I had ice coming out within 30 minutes!

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Ice Maker Assembly - 8 Cube

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsPliers, Socket set

CustomerPaul from San Antonio TX

Ice maker would not work at all-someone used inappropriately.

we ordered the complete ice maker assembly, since we were unsure as to which part was broken. It was extremely easy to replace and our ice maker is perfect!!! The price was very reasonable. This is a great company!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Ice Maker Assembly - 8 Cube

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerLance from Angels Camp CA

No ice

Removed defective icemaker. Used nutdriver to remove screws. Pull ou old unit. Disassemble old unit to use required parts to attach to the new unit. Slide in new unit but encountered problem with the fill funnel height. This was different than the original unit. I had to bend up the rubber fill spout in order to slide in the icemaker. This took several attempts because there is not much clearance. Installed screw and icemaker was back in action.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Ice Maker Assembly - 8 Cube

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers, Socket set

CustomerGerald N from Flidell LA

Ice maker stopped making ice

Unsrewed 6 screws, pulled out old icemaker, unplugged the connecting wiring and pluged in new icemaker and slid it back into the mountings. Re installed the 6 screws and closed the door, within 3 hours we had ice again. Very easy!

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

  • Ice Maker Assembly - 8 Cube

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerLes from Cicero IN

No ice or cycling of icemaker

This model uses light sensors to control the icemaker. After determining that the light and sensors operate correctly, the problem is either the icemaker module or the valve. After 6 years there was visible corrosion on the blades, so I selected the entire assembly for about $40 more. The new unt fit perfectly. Wait a while 2-4 hours to see if it works, it is not right away.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 5 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerTim from Franklin OH

Ice maker would not work

removed front door. removed one screw on wireharness cover. slid icemaker out. disconnected wireharness. removed bottom 3 remaining screws. reversed process to reinstall.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

  • Ice Maker Assembly - 8 Cube

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerRichard from St Pete Beach FL

Stopped working properly

Easily remove and replaced with new one. Do this yourself if you have ice maker problem don't call for service.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

  • Ice Maker Assembly - 8 Cube

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerMark from King William VA

Ice maker stopped working

The replacement was an almost exact match, except for the plastic sidewall that needed a hole in it for the water supply shoot. Just removed a couple screws, and reattached the old one. A wire harness and three screws later, and we were making ice.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

  • Ice Maker Assembly - 8 Cube

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Pliers

CustomerJEFFERY from WAVELAND MS

Stopped making ice

Turn power off to Ice Maker. First I had to remove the Ice Maker Door by removing the two 1/4" screws.
I then removed the 1/4" screw under the Ice Maker on the right hand side that holds the wire cover in place. The cover can be removed by pulling toward the rear at a angle. Now you can slide the Ice Maker forward until it out and only connected by the wire harness which can now be unplugged
The bottom plate on the old Ice Maker will need to be removed and installed on the new one.
Now just work in reverse.

Help other customers find the most helpful instructions.

Were these instructions helpful?