Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS869316
This icemaker can be used with 25-27 cubic feet refrigerators that have a vertical auger dispenser located on the freezer door. Reuse bottom bracket from the original icemaker and attach to the new.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
Removed 3 screws but was unable to remove without removing another screw for better access to disconnect wiring harness. Then had to really almost force unit out of the holder. Quoted price was $177. If I ordered by 3:00pm the next day would be shipped just as promtly. The only thing is the next morning when I called the price was $201. because of manufacturers price increases. I was billed $201 plus shipping even though they had the item in stock and had received it at the old price. Don't put off till tomorrow what you can do today.
Help other customers find the most helpful instructions.
Were these instructions helpful?
turned off the machine. removed the ice maker door. removed the wiring harness cover. press on locking clips, removed ice maker. disconnect wiring harness. removed three screws from cover and installed on new ice maker. installed in reverse order of removable.
I was meaning to call a repair service when a co-worker told me he fixed his washer machine after watching a you tube video. I went home and watched a video that both diagnosed the problem and told me what to look for to determine which part need replacing. I ordered the replacement icemaker unit and it arrived in time for the weekend. The whole process took about 15 minutes and I had a full bin of ice in about a day. I'm sure this saved me hundreds of dollars. Very easy.
Previously replaced by repairman for $300+. Did it myself this time for cost of part. It was just 3 screws, slide it out and then plug in the new.
Turn power off to Ice Maker. First I had to remove the Ice Maker Door by removing the two 1/4" screws.I then removed the 1/4" screw under the Ice Maker on the right hand side that holds the wire cover in place. The cover can be removed by pulling toward the rear at a angle. Now you can slide the Ice Maker forward until it out and only connected by the wire harness which can now be unplugged The bottom plate on the old Ice Maker will need to be removed and installed on the new one.Now just work in reverse.
I slid out the old ice maker, about two screws. Then installed the new one it took about 7 minutes. Very easy.
I have not completed the repair. I know what needs to be done, but I cannot loosen the screws to remove the icemaker. I'll probably finish the work but calling a repairman to do the installation.
If you can turn a screwdriver you can replace this thing. After 10 minutes the new icemaker was installed, and 5 hours later I was enjoying a cocktail with my newly made ice.
I spent quite a bit of time diagnosing the problem. When the ice maker first stopped working, I noticed the fingers that push out ice where pointing straight down and frozen within the cubes. I pulled out the ice maker and let it thaw so I could move the fingers again. The gear that turns the assembly was not in the correct position after several tries, I finally realized that the heater element wasn't working, so when the fingers started to push out the cubes, they would stick and the gear became stripped.In the end, I replaced the whole unit which wasn't cheap, but was making cubes within an hour of installing the new unit.
My Ice Maker would stop making ice and the start back. Finally it quit for good and would not work any longer. The repair was as easy as everone indicated and I am sure that I saved more than half of the cost of calling a repairman. Is used a 1/4 socket and a small ratched. Took less than 15 minutes to completely change out the unit. Thanks for being on the internet. Super cost for the complet unit.
Our 2nd Ice-maker since 2003. They don't last forever. Intact, the Ice-maker takes 15 minutes to swap out. Broken, we wait for a replacement. Ordered extra Fill Cup. Not needed. Different Part broken this time! Latest Ice-maker has an extended Fill Cup so as not to Freeze up when refilling. Nice! When Trays lose their lining or Unit Freezes up, time to replace it! The Ice-maker should last longer. Maybe we expect too much. We like our ice!
First I removed the ice tray door by lifting and then releasing the hinge. Then I used a nutdriver and socket to remove three recessed screws that are located under the icemaker. I also removed the screw on the underside which holds a plastic flange in place covering the wiring harness. Remove the plastic flange and slide the icemaker out as far as possible, then disconnect the wiring harness from the icemaker. Slide the old unit out and discard. Reverse the procedure to install the new unit. Points of frustration: Disconnecting the wiring harness--it is in there mighty tight! Also, when sliding the new unit into place, clearing the rubber water spout without breaking something is somewahat of a challenge. The unit comes outeasier than it goes back in!
i ordered the instructions and then learned the icemaker assembly was bad and easily replaced it. saved money on having to hire a repairman (i am a 35 yr old pregnant woman btw :)) thanks www.partselect.com.
The video on the web site made this repair easy.
We removed the old icemaker, that was the easy part. It only has one bolt holding it in place. The tricky part was installing the new one. The replacement icemaker was a little different than the original, but it fit and works great. Simple connect the wires insert the icemaker, screw the bolt in place and viola. The shipping was so much faster than I had expected. My first order was received broken but they immediately sent a replacement and I got it the next day. It was hassle free and our first time replacing the icemaker went smoothly.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.