Ice Maker Assembly - 8 Cube

PartSelect Number PS869316

This icemaker can be used with 25-27 cubic feet refrigerators that have a vertical auger dispenser located on the freezer door. Reuse bottom bracket from the original icemaker and attach to the new.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Ice maker not making ice.
  • Ice maker won’t dispense ice.
  • Leaking.
  • Won’t start.
  • Compare At

    $132.55
  • You Save

    $22.09
  • Your Price

    $110.46
In Stock
Order within the next 8 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.1 / 5.0, 83 reviews What's this?
1-5 of 83
 

352 of 371 people found this instruction helpful

Parts Used

  • Ice Maker Assembly - 8 Cube

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerPhil from Auberry, CA

Ice maker stopped functioning

Remove the icemaker service door... gently pry the door pins from the hinge sockets. Remove the 3 screws from the under side of the icemaker with a nut driver (1/4"). Gently remove the icemaker . It's a tight fit between the top of the compartment and the icemaker lower support tray. Next, disconnect the electrical connector at the right side. You're done! Reverse procedure for installing. Good luck. Remember, your working with cold plastic...take your time and don't force too much.

Help other customers find the most helpful instructions.

Were these instructions helpful?

71 of 78 people found this instruction helpful

Parts Used

  • Ice Maker Assembly - 8 Cube

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerJames from Puyallup, WA

Ice maker quit working

First called the Sears repairman out (big mistake). I was worried it was something with the water line, but he ran some diagnostics and got it working. It did make one batch of ice. Cost $140 for the visit. The "fix" was short lived, since it immediately quit working again. After doing lots of reading online, all I could gather was that the main wheel inside was out of alignment/sync. Sears has a 90-day warranty on repairs, so we called them back. Of course, their warranty only covers their previous repair only, but at least we wouldn't get charged the $55 fee just to have them come out. Second repairman said there was a broken part inside the icemaker assembly, and it would cost over $320 to fix this time ($230 for the part, $70 for labor, plus tax). We politely declined. Found a whole new icemaker assembly from PartSelect for $68. Once it arrived, it was literally just three screws/bolts holding in the entire assembly, unplug the wire chassis, just like a computer motherboard, insert new assembly, plug in wire assembly, put screws back in. Works like a champ...

Help other customers find the most helpful instructions.

Were these instructions helpful?

41 of 53 people found this instruction helpful

Parts Used

  • Ice Maker Assembly - 8 Cube

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerKeith from St. Peters, MO

My icemaker stopped working. I think the motor was too weak to release the cubes

Removed two screws and popped loose the ice door. Disconnected the single electrical connector. Slid out the old, slide in the new. It worked like a charm. - Still dissappointed that the whirlpool icemaker broke after only 2 years, but the new one works great!

Help other customers find the most helpful instructions.

Were these instructions helpful?

26 of 31 people found this instruction helpful

Parts Used

  • Ice Maker Assembly - 8 Cube

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerLarry from Morgan, TX

Ice maker did not work. Water came in, however, unit woud not eject ice.

I unplugged the refrigerator, then I taped ice shield up to top of refrigerator and taped the little flap on the left side of the refrigerator to side wall then I unscrewed one screw on the right side that holds the plug cover, which was then removed. I then updid the little latches on the icemaker and pulled the old ice maker out far enough to unplug the connector, which was not easy, but did unplug. I then unscrewed the three screws with the nutdriver and attached the bottom cover to the new ice maker. I then slid the new icemaker far enough to connect the electrical connector, then slid the new icemaker in until it latched. I replaced the connector cover and untaped the two items that had been taped and pluged the refrigerator into the wall socket. The new icemaker has produced ice every since.

Help other customers find the most helpful instructions.

Were these instructions helpful?

15 of 17 people found this instruction helpful

Parts Used

  • Ice Maker Assembly - 8 Cube

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerNeil from Berlin, MD

Not making ice

I took a 1/4 nut driver and removed the wire cover. I then used a small screwdriver to push up the clips the lock the unit in place. I then unplugged the unit and removed. I then used the same nut driver and removed the bottom plastic cover and installed it on the new icemaker. I then put the new unit part way back onto it slides, being carful to make sure the water fill spout clears the unit. Next I plugged in the wire harness and then slid the unit the rest of the way in until it locked in place. I then reinstalled the wire cover.
This unit was delivered at 1:30 and it was installed by 2

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 83