Quick Question!

Have you ever purchased from PartSelect.com before?

869316-1-S-Whirlpool-2198597           -Ice Maker Assembly -  8 Cube
869316-1-S-Whirlpool-2198597           -Ice Maker Assembly -  8 Cube 869316-2-S-Whirlpool-2198597           -Ice Maker Assembly -  8 Cube 869316-3-S-Whirlpool-2198597           -Ice Maker Assembly -  8 Cube http://www.partselect.com/Schematics/Maytag/1GORO42Y.gif

Ice Maker Assembly - 8 Cube

PartSelect Number PS869316

This icemaker can be used with 25-27 cubic feet refrigerators that have a vertical auger dispenser located on the freezer door. Reuse bottom bracket from the original icemaker and attach to the new.

This part works with the following brands: Whirlpool, Kenmore, KitchenAid, Maytag.

This part works with the following products: Refrigerator.

This part fixes the following symptoms:

  • Ice maker not making ice.
  • Ice maker won’t dispense ice.
  • Leaking.
  • Won’t start.
  • Ice maker dispenses too little ice.

Compare At

$149.17

You Save

$24.86

Your Price

$124.31
Order within the next 10 hrs and your part ships today!
Get this part fast. Average delivery time via standard shipping: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.1 / 5.0, 95 reviews What's this?
 

2 of 5 people found this instruction helpful

Parts Used:
  • Ice Maker Assembly - 8 Cube
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver
Customer: Michael from Kings Mountain, NC

Ice maker would not kick out ice, but pump worked

I unpluged unit empty top shelf took out 4 screws
holding ice maker slid it forward unplug harness
found out that the wheel inside ice maker was not
lined up with the letter T on the front of wheel, that would put the fingers in the upright position. so it will work.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 3 people found this instruction helpful

Parts Used:
  • Ice Maker Assembly - 8 Cube
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver, Pliers
Customer: JEFFERY from WAVELAND, MS

Stopped making ice

Turn power off to Ice Maker. First I had to remove the Ice Maker Door by removing the two 1/4" screws.
I then removed the 1/4" screw under the Ice Maker on the right hand side that holds the wire cover in place. The cover can be removed by pulling toward the rear at a angle. Now you can slide the Ice Maker forward until it out and only connected by the wire harness which can now be unplugged
The bottom plate on the old Ice Maker will need to be removed and installed on the new one.
Now just work in reverse.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 3 people found this instruction helpful

Parts Used:
  • Ice Maker Assembly - 8 Cube
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: David from Antioch, CA

Ice maker broken

I slid out the old ice maker, about two screws. Then installed the new one it took about 7 minutes. Very easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 6 people found this instruction helpful

Parts Used:
  • Ice Maker Assembly - 8 Cube
Level of Difficulty: Really Easy
Time to do repair: 1- 2 hours
Tools: Nutdriver, Socket set
Customer: Cheryl from Conroe, TX

Icemaker is "overfilling" and dripping into the freezer.

I have not completed the repair. I know what needs to be done, but I cannot loosen the screws to remove the icemaker. I'll probably finish the work but calling a repairman to do the installation.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 3 people found this instruction helpful

Parts Used:
  • Ice Maker Assembly - 8 Cube
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver, Screw drivers
Customer: Jason from Mount Horeb, WI

Icemaker not making ice

If you can turn a screwdriver you can replace this thing. After 10 minutes the new icemaker was installed, and 5 hours later I was enjoying a cocktail with my newly made ice.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 3 people found this instruction helpful

Parts Used:
  • Ice Maker Assembly - 8 Cube
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Pliers
Customer: Steve from Bothell, WA

Ice maker stopped working

I spent quite a bit of time diagnosing the problem. When the ice maker first stopped working, I noticed the fingers that push out ice where pointing straight down and frozen within the cubes. I pulled out the ice maker and let it thaw so I could move the fingers again. The gear that turns the assembly was not in the correct position after several tries, I finally realized that the heater element wasn't working, so when the fingers started to push out the cubes, they would stick and the gear became stripped.

In the end, I replaced the whole unit which wasn't cheap, but was making cubes within an hour of installing the new unit.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 3 people found this instruction helpful

Parts Used:
  • Ice Maker Assembly - 8 Cube
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver, Socket set
Customer: James from Kerrville, TX

Ice maker would quit making ice, off and on

My Ice Maker would stop making ice and the start back. Finally it quit for good and would not work any longer. The repair was as easy as everone indicated and I am sure that I saved more than half of the cost of calling a repairman. Is used a 1/4 socket and a small ratched. Took less than 15 minutes to completely change out the unit. Thanks for being on the internet. Super cost for the complet unit.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 6 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Gill from Katy, TX

Icemaker not working

Our 2nd Ice-maker since 2003. They don't last forever.
Intact, the Ice-maker takes 15 minutes to swap out. Broken, we wait for a replacement. Ordered extra Fill Cup. Not needed. Different Part broken this time! Latest Ice-maker has an extended Fill Cup so as not to Freeze up when refilling. Nice!

When Trays lose their lining or Unit Freezes up, time to replace it! The Ice-maker should last longer. Maybe we expect too much. We like our ice!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 3 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers, Socket set
Customer: Ron from Bremerton, WA

Ice maker wouldn't work.

First I removed the ice tray door by lifting and then releasing the hinge. Then I used a nutdriver and socket to remove three recessed screws that are located under the icemaker. I also removed the screw on the underside which holds a plastic flange in place covering the wiring harness. Remove the plastic flange and slide the icemaker out as far as possible, then disconnect the wiring harness from the icemaker. Slide the old unit out and discard. Reverse the procedure to install the new unit. Points of frustration: Disconnecting the wiring harness--it is in there mighty tight! Also, when sliding the new unit into place, clearing the rubber water spout without breaking something is somewahat of a challenge. The unit comes out
easier than it goes back in!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 3 people found this instruction helpful

Parts Used:
  • Ice Maker Assembly - 8 Cube
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: rebecca from pflugerville, TX

No ice was being made

i ordered the instructions and then learned the icemaker assembly was bad and easily replaced it. saved money on having to hire a repairman (i am a 35 yr old pregnant woman btw :)) thanks www.partselect.com.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 3 people found this instruction helpful

Parts Used:
  • Ice Maker Assembly - 8 Cube
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver
Customer: R C from Brimfield, IL

Ice maker not producing ice

First tested the water control valve on back to make sure water was getting to the ice maker. Then, replaced ice maker. Old Ice maker was easy to remove and new one was just as easy to install. Simply slide out the ice maker diconnect at the wire connector, connect new ice maker and slide back in. Turn on ice maker and began producing ice.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Ice Maker Assembly - 8 Cube
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Colleen from Kennedale, TX

Ice maker quit working

The video on the web site made this repair easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Ice Maker Assembly - 8 Cube
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Socket set
Customer: Michelle from Cibolo, TX

Icemaker stopped making ice

We removed the old icemaker, that was the easy part. It only has one bolt holding it in place. The tricky part was installing the new one. The replacement icemaker was a little different than the original, but it fit and works great. Simple connect the wires insert the icemaker, screw the bolt in place and viola. The shipping was so much faster than I had expected. My first order was received broken but they immediately sent a replacement and I got it the next day. It was hassle free and our first time replacing the icemaker went smoothly.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Ice Maker Assembly - 8 Cube
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Kevin from Madison, CT

Ice maker stopped working

I searched the internet and found a detailed instructions list (with pics). The written instructions on Partselect.com were on the money but the pics really helped! Start to finish, the entire job took 15 minutes. If you're the least bit handy, this is an easy one!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Ice Maker Assembly - 8 Cube
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver, Screw drivers
Customer: Rex from Hilliard, OH

Quit making ice

The first maker I received was broken. The funnel at the top that directs the water into the tray was broken. I called PartSelect and told them how I had received the part and there was no problem. They shipped me a new part, and it must have been the same day as I got the replacement two days later. I was very satisfied with that quick response. I removed one screw and the cover to the wiring harness. Slid the icemaker forward and unplugged the wiring. Then removed the icemaker. I had to remove the old bracket from the assembly as the new maker did not come with one. Installed three screws in bottom of bracket then reinstalled the assembly and plugged the wiring back in. The whole process took about 10 to 12 minutes, very easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?