Quick Question!

Have you ever purchased from PartSelect.com before?

869316-1-S-Whirlpool-2198597           -Ice Maker Assembly -  8 Cube
869316-1-S-Whirlpool-2198597           -Ice Maker Assembly -  8 Cube 869316-2-S-Whirlpool-2198597           -Ice Maker Assembly -  8 Cube 869316-3-S-Whirlpool-2198597           -Ice Maker Assembly -  8 Cube http://www.partselect.com/Schematics/Maytag/1GORO42Y.gif

Ice Maker Assembly - 8 Cube

PartSelect Number PS869316

Manufacturer Part Number 2198597
Manufactured by Whirlpool

This icemaker can be used with 25-27 cubic feet refrigerators that have a vertical auger dispenser located on the freezer door. Reuse bottom bracket from the original icemaker and attach to the new.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Ice maker not making ice.
  • Ice maker won’t dispense ice.
  • Leaking.
  • Won’t start.
  • Ice maker dispenses too little ice.

Compare At

$149.27

You Save

$24.88

Your Price

$124.39
Order within the next 9 hrs and your part ships today!
Get this part fast. Average delivery time via standard shipping: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.1 / 5.0, 90 reviews What's this?
76-90 of 90
 

0 of 1 people found this instruction helpful

Parts Used:
  • Ice Maker Assembly - 8 Cube
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver
Customer: TERRI from SARASOTA, FL

Not making ice

slide old ice maker out, unplug, plug new ice maker in, slide in place

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Ice Maker Assembly - 8 Cube
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: Rob from Round Rock, TX

Ice maker would not produce ice

I disassembled original ice maker to find a short between the motor housing and the tray heater. Easiest to replace full assembly. Ordered new part, and after it arrived...

Removed front ice maker door and rear power wire cover. Slide out ice maker and removed the reusable parts and installed on new assembly. Installed new ice maker in reverse. Ice maker immediately filled with water but never went into harvest mode. I figured the optics board was bad, but it wasn't. I removed the transmitter and receiver, and let them warm to room temperature and reinstalled after cleaning optics with cotton swab. The ice maker started working like a charm.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Ice Maker Assembly - 8 Cube
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Socket set
Customer: william from Chesapeake, AL

My ice maker quit making ice

I unbolted the old ice maker, pulled it out, unplugged it and then I put in the new one...it was exactly the same. I had ice coming out within 30 minutes!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Ice Maker Assembly - 8 Cube
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Pliers, Socket set
Customer: Paul from San Antonio, TX

Ice maker would not work at all-someone used inappropriately.

we ordered the complete ice maker assembly, since we were unsure as to which part was broken. It was extremely easy to replace and our ice maker is perfect!!! The price was very reasonable. This is a great company!!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Ice Maker Assembly - 8 Cube
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers
Customer: Lance from Angels Camp, CA

No ice

Removed defective icemaker. Used nutdriver to remove screws. Pull ou old unit. Disassemble old unit to use required parts to attach to the new unit. Slide in new unit but encountered problem with the fill funnel height. This was different than the original unit. I had to bend up the rubber fill spout in order to slide in the icemaker. This took several attempts because there is not much clearance. Installed screw and icemaker was back in action.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Ice Maker Assembly - 8 Cube
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers, Socket set
Customer: Gerald N from Flidell, LA

Ice maker stopped making ice

Unsrewed 6 screws, pulled out old icemaker, unplugged the connecting wiring and pluged in new icemaker and slid it back into the mountings. Re installed the 6 screws and closed the door, within 3 hours we had ice again. Very easy!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 2 people found this instruction helpful

Parts Used:
  • Ice Maker Assembly - 8 Cube
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver
Customer: Les from Cicero, IN

No ice or cycling of icemaker

This model uses light sensors to control the icemaker. After determining that the light and sensors operate correctly, the problem is either the icemaker module or the valve. After 6 years there was visible corrosion on the blades, so I selected the entire assembly for about $40 more. The new unt fit perfectly. Wait a while 2-4 hours to see if it works, it is not right away.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 2 people found this instruction helpful

Parts Used:
  • Ice Maker Assembly - 8 Cube
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver
Customer: Richard from St Pete Beach, FL

Stopped working properly

Easily remove and replaced with new one. Do this yourself if you have ice maker problem don't call for service.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 2 people found this instruction helpful

Parts Used:
  • Ice Maker Assembly - 8 Cube
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver
Customer: Mark from King William, VA

Ice maker stopped working

The replacement was an almost exact match, except for the plastic sidewall that needed a hole in it for the water supply shoot. Just removed a couple screws, and reattached the old one. A wire harness and three screws later, and we were making ice.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 2 people found this instruction helpful

Parts Used:
  • Ice Maker Assembly - 8 Cube
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver
Customer: R C from Brimfield, IL

Ice maker not producing ice

First tested the water control valve on back to make sure water was getting to the ice maker. Then, replaced ice maker. Old Ice maker was easy to remove and new one was just as easy to install. Simply slide out the ice maker diconnect at the wire connector, connect new ice maker and slide back in. Turn on ice maker and began producing ice.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 3 people found this instruction helpful

Parts Used:
  • Ice Maker Assembly - 8 Cube
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver, Wrench set
Customer: James from Moulton, TX

Quit making ice

First I cut the icemaker off. Then I removed the screw to the wire cover,next the two screws to the icemaker door, pushed in the retainer clips on the bottom of unit, pulled the unit forward, disconnected the wire harness.Remove the bottom of old unit, attach it to new unit . Plug in the wire harness , push the unit in re-assemble wire cover, ice maker door. Turn ice maker on.
Less then 2 min. it filled with water. Droped ice about 1 hr. later. That was sweet music to my ears.
Has been making ice every day. I'm glad I orderd the icemaker from Part Select, I waited 5 months for a repairman to get back to repair the unit. Wasnt that difficult to replace. Peace of cake.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 3 people found this instruction helpful

Parts Used:
  • Ice Maker Assembly - 8 Cube
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Socket set
Customer: Walter from Victoria, TX

Replaced ice maker with new. Went very easy and partselect sent everything I needed

Disconnected power supply and removed back screw which released ice maker from freezer. Removed bottom plate from old ice maker held in place by three additional screws, attached to new ice maker and re-installed. Very simple replacement and I would order again from PartSelect.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 3 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver
Customer: Frank from Omaha, NE

Ice maker stoped working

removed old unit, and replaced with new one found
the job to be very simple. I hand no problems.
and the unit is working fine.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 6 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers, Socket set
Customer: Damon from Cedar Park, TX

Ice maker would not make ice

I ordered a new ice maker because at least a couple of the parts on my old one were broken. I also ordered the valve because I wasn't sure that wasn't also the problem (turns out it was still functional). I removed the ice maker cover, one screw that held a shroud over the water inlet, another screw that held the ice maker to the inside of the freezer, disconnected the wire harness, and slid the ice maker out. I reversed the procedure to install the new one. It was a real breeze! I have returned the valve to Partselect and have been making ice ever since. SO much easier than buying bags of ice all the time!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 13 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver
Customer: Tim from Franklin, OH

Ice maker would not work

removed front door. removed one screw on wireharness cover. slid icemaker out. disconnected wireharness. removed bottom 3 remaining screws. reversed process to reinstall.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

76-90 of 90