869316-1-S-Whirlpool-2198597           -Ice Maker Assembly -  8 Cube
869316-1-S-Whirlpool-2198597           -Ice Maker Assembly -  8 Cube 869316-2-S-Whirlpool-2198597           -Ice Maker Assembly -  8 Cube 869316-3-S-Whirlpool-2198597           -Ice Maker Assembly -  8 Cube http://www.partselect.com/Schematics/Maytag/1GORO42Y.gif

Ice Maker Assembly - 8 Cube

PartSelect Number PS869316

Manufacturer Part Number 2198597
Manufactured by Whirlpool

This icemaker can be used with 25-27 cubic feet refrigerators that have a vertical auger dispenser located on the freezer door. Reuse bottom bracket from the original icemaker and attach to the new.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Ice maker not making ice.
  • Ice maker won’t dispense ice.
  • Leaking.
  • Won’t start.
  • Compare At

    $133.67
  • You Save

    $22.28
  • Your Price

    $111.39
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.1 / 5.0, 83 reviews What's this?
 

3 of 3 people found this instruction helpful

Parts Used:
  • Ice Maker Assembly - 8 Cube
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver
Customer: Tim from West Palm Beach, FL

Icemaker worked intermittently then not at all.

I removed two small bolts that secure the flapper that keeps ice from falling out when you open the door, one bolt that holds a cosmetic cover for the wires and slid the icemanker forward. The only difficult part was removing the plug since it was high up, the wires were stiff and there's a release to push that locks the two plugs together. Once it was removed all was installed in the opposire order.
The part I ordered had a slightly taller channel where the water refills so I had to trim it to allow the new icemaker to slide in without bending the fill nozzle. Other than that it was pretty easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used:
  • Ice Maker Assembly - 8 Cube
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Nutdriver
Customer: DAVID from ROSEBURG, OR

No ice

I could have bought the "brains" of the ice maker, but decided to replace the whole ice and make sure the problem was fixed. This refrig was let in home I just bought, so do not know its history. The biggest problem was trying to get the ice maker out of the tight spot without applying undo pressure on any part. It finally came out. The next problem was figuring out the catch on plug-in for electrial power. That done, the new ice maker went in without a hitch and is making ice. Glad I decided to order the part and do it myself for the cost of a service charge -- and not service call and part.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used:
  • Ice Maker Assembly - 8 Cube
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Alan from Phoenixville, PA

Icemaker stopped making ice

Installing the new icemaker is simple. The only problem I had was disconnecting the wiring. Had to use pliers to gently pull the plugs apart. After that, installing the new one was relatively easy. It's a tight fit but can be accomplished with big American hands ;-). After about 15 minutes, it starting making ice again.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used:
  • Ice Maker Assembly - 8 Cube
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver
Customer: Peter K from Santa Ana, CA

Icemaker stopped making ice

First thought it might've been a problem with the inlet valve assembly but it wasn't. Took the factory unit out of the refrigerator and from testing found out one of the wires (black) was busted so splice a new wire in and motor started working but the "arm" would only rotate to a certain point and stop. I then discovered a broken tab inside the motor housing so at the point I just ordered a brand new icemaker unit. When I got it, I just mounted it to the base plate then slid it into the tracks in the refrigerator. The spout where the water comes out was the only tricky part but it is flexible so you just have to push it away and put it back into the tray when the whole unit is inserted. Once inserted, connect the power to the refrigerator, lock the wire cover to the base plate and you should be fine. The new unit started working right away. Whole process took 5 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used:
  • Ice Maker Assembly - 8 Cube
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Socket set, Wrench (Adjustable)
Customer: Chantel from El Paso, TX

Ice maker quit making ice.

This was relatively easy, but did require patience. First I removed the ice maker door cover, then the bolts, which required a socket and wrench. Next the icemaker wires had to be disconnected, it was a little tough - the connection was on there tight. Once the old unit is out, make sure you remove the motor cover and bracket - you need those on the new one before it goes in. After replacing the bracket and motor cover on the new unit, you connect the wires, pop in the new unit and put all the bolts back in. It was mostly a one person job, but I did need a second set of hands when disconnecting and connecting the wires.

Help other customers find the most helpful instructions.

Were these instructions helpful?